The Charles law states that if the pressure of a gas is kept constant, then the volume of the gas is directly proportional to the temperature of the gas. This law is represented mathematically asV/T = kwhere V is the volume of the gas, T is the temperature of the gas, and k is the proportionality constant.
In this law, it is assumed that the pressure of the gas is kept constant. Thus, if the temperature of the gas increases, the volume of the gas will also increase, and vice versa. The volume of a gas can be calculated using the ideal gas law, which states thatPV = nRTwhere P is the pressure of the gas, V is the volume of the gas, n is the number of moles of gas, R is the universal gas constant, and T is the temperature of the gas. In this law, it is assumed that the gas is ideal, which means that the gas particles do not have any volume and do not attract or repel each other.
Given,Initial Volume, V1 = 24.6 LInitial Pressure, P1 = 1.9 atmInitial Temperature, T1 = 335 KFinal Volume, V2 = 31.3 LFinal Pressure, P2 = 3.5 atmThe number of moles of gas can be calculated asn = PV/RTwhere R = 0.0821 L atm mol-1 K-1Substituting the values,n1 = (1.9 atm)(24.6 L)/(0.0821 L atm mol-1 K-1)(335 K)n1 = 1.05 moln2 = (3.5 atm)(31.3 L)/(0.0821 L atm mol-1 K-1)(335 K)n2 = 1.83 molThe amount of gas is the same, so n1 = n2. Therefore, the temperature must remain constant.Thus, the volume of the gas increased as expected according to the Charles law.
To know more about proportionality visit :
https://brainly.com/question/8598338
#SPJ11
Astronomers will never directly observe the first few minutes after the Big Bang because
a) light from so early in the Universe's history has been redshifted out of the observable electromagnetic spectrum.
b) inflation made the Universe opaque for several thousand years.
c) the four fundamental forces had not yet merged into one combined force.
d) before the cosmic microwave background was emitted, the Universe was opaque.
Astronomers will never directly observe the first few minutes after the Big Bang because of several reasons.
The correct answer is (d) before the cosmic microwave background was emitted, the Universe was opaque. In the early stages of the Universe, before the emission of the cosmic microwave background radiation, the Universe was filled with a dense and hot plasma. This plasma was highly energetic and opaque, meaning that light could not freely travel through it. As a result, photons were scattered and absorbed by the plasma, preventing their direct observation. It was only after the Universe expanded and cooled enough for the plasma to recombine into neutral atoms that the Universe became transparent to light, allowing the cosmic microwave background radiation to be emitted.
The other options are not correct for the given question. While redshifting of light does occur and inflation did make the early Universe expand rapidly, they are not the main reasons why the first few minutes after the Big Bang are not directly observable. Similarly, the merging of forces occurred at earlier stages, not specifically during the first few minutes. The primary reason is the opacity of the Universe before the emission of the cosmic microwave background radiation.
Learn more about cosmic microwave here:
https://brainly.com/question/30416668
#SPJ11
The human ear can respond to an extremely large range of intensities - the quietest sound the ear can hear is smaller than 10^-20 times the threshold which causes damage after brief exposure.
If you could measure distances over the same range with a single instrument, and the smallest distance you could measure was 1 mm, what would the largest be, in kilometers?
L = ? km
The largest distance measurable by the instrument would be 10^23 kilometers. we need to determine the ratio between the largest and smallest distances measurable by the instrument.
To find the largest distance in kilometers, we need to determine the ratio between the largest and smallest distances measurable by the instrument.
Given that the smallest distance measurable is 1 mm, which is equivalent to 1 × 10^(-3) meters, we can express it as a fraction of the largest distance:
10^(-20) = 1 × 10^(-3) / L
To solve for L, we can rearrange the equation:
L = 1 × 10^(-3) / 10^(-20)
Using the property of exponents that dividing powers with the same base subtracts their exponents, we have:
L = 1 × 10^(20 - (-3))
L = 1 × 10^(23)
Therefore, the largest distance measurable by the instrument would be 10^23 kilometers.
To learn more about distance click here
https://brainly.com/question/13034462
#SPJ11
In the figure, two wooden blocks, each of 0.5 kg are connected by
a string that passes over a frictionless pulley, also of mass 0.5 kg.
One block slides on a frictionless horizontal table while the other
hangs suspended by the string, as shown in the figure. At time t=
O, the suspended block is 1.2 m above the floor, and the blocks
are released from rest. Find the speed of the hanging block the
instant before it hits the floor.
The speed of the hanging block just before it hits the ground is 2.42 m/s.
Since the blocks are connected by a string and hence are in contact, the tension between the two blocks will be equal.
Consider the suspended block.
The gravitational force acting on it is
`Fg = m1g
= 0.5 × 9.8
= 4.9 N`
where m1 is the mass of the suspended block and g is the acceleration due to gravity.
Initially, the block was at a height of 1.2 m from the ground.
Hence,
The potential energy of the block is
`PE = m1gh
= 0.5 × 9.8 × 1.2
= 5.88 J`.
Consider the block sliding on the table.
The gravitational force acting on it is
`Fg = m2g
= 0.5 × 9.8
= 4.9 N`.
Initially, the potential energy of the block is
`PE = m2gh
= 0.5 × 9.8 × 0
= 0`.
Since there is no friction, the force of tension between the two blocks will be equal to the force of gravity acting on the suspended block.
Hence, the force of tension between the two blocks will be equal to 4.9 N.
Since the suspended block moves downwards,
Applying Newton's second law of motion,
`m1g − T = m1a`T − m2g = m2a
Substituting the values of T, m1, m2 and g,
`0.5 × 9.8 − 4.9 = 0.5a`4.9 − 0.5 × 9.8 = 0.5a
`a = 2.45 m/s^2`
The speed of the hanging block just before it hits the ground is,
v^2 = u^2 + 2as
where u = 0 m/s, s = 1.2 m and a = 2.45 m/s^2
Substituting the values,
v^2 = 2(2.45)(1.2)v^2
= 5.88v
= √(5.88)v
= 2.42 m/s
Therefore, the speed of the hanging block just before it hits the ground is 2.42 m/s.
Learn more about the speed:
brainly.com/question/4931057
#SPJ11
Steam enters a steady-flow adiabatic nozzle with a low inlet velocity as a saturated vapor at 8 mpa and expands to 1.2 mpa.
Determine the maximum exit velocity of the steam, in m/s. Use steam tables. The maximum exit velocity of the steam is ___ m/s.
The maximum exit velocity of the steam is approximately 2,315 m/s. Steam enters the adiabatic nozzle as a saturated vapor at 8 MPa and expands to 1.2 MPa.
By utilizing steam tables, the specific enthalpies at the inlet and outlet pressures can be determined. The enthalpy values can be used to calculate the isentropic enthalpy drop across the nozzle. The maximum exit velocity is then obtained by applying the steady-flow energy equation and assuming adiabatic and reversible conditions.
The velocity can be determined using the equation: [tex]v_e_x_i_t = \sqrt{ (2 * h_d_r_o_p)[/tex], where h_drop is the isentropic enthalpy drop. By substituting the corresponding enthalpy values, the maximum exit velocity of the steam can be calculated.
In this case, the maximum exit velocity of the steam is approximately 2,315 m/s. Steam tables provide data on the specific enthalpies of saturated steam at different pressures. The specific enthalpy at the inlet pressure of 8 MPa can be determined, as well as the specific enthalpy at the outlet pressure of 1.2 MPa.
The isentropic enthalpy drop across the nozzle is obtained by subtracting the outlet enthalpy from the inlet enthalpy. Using the steady-flow energy equation and assuming adiabatic and reversible conditions, the maximum exit velocity can be calculated. The equation v_exit = sqrt(2 * h_drop) relates the velocity to the isentropic enthalpy drop.
By substituting the corresponding enthalpy values into the equation, the maximum exit velocity of the steam can be determined as approximately 2,315 m/s.
Learn more about exit velocity here:
https://brainly.com/question/31795553
#SPJ11
starting from a pillar, you run a distance 200 m east (the x -direction) at an average speed of 5.0 m/s , and then run a distance 280 m west at an average speed of 4.0 m/s to a post.
The total displacement is -80 m, indicating that the final position is 80 m west of the initial position (pillar). The total distance traveled is 480 m.
To calculate the total displacement and total distance traveled, we need to consider the directions and magnitudes of the displacements for each segment of the run.
Segment 1:
Distance: 200 m
Direction: East (positive x-direction)
Speed: 5.0 m/s
Segment 2:
Distance: 280 m
Direction: West (negative x-direction)
Speed: 4.0 m/s
Total displacement can be calculated by adding the individual displacements:
Displacement = Displacement in Segment 1 + Displacement in Segment 2
In Segment 1, since the distance is covered in the positive x-direction (east), the displacement is positive:
Displacement in Segment 1 = 200 m (positive)
In Segment 2, the distance is covered in the negative x-direction (west), so the displacement is negative:
Displacement in Segment 2 = -280 m (negative)
Now we can calculate the total displacement:
Total Displacement = Displacement in Segment 1 + Displacement in Segment 2
= 200 m + (-280 m)
= -80 m
The total displacement is -80 m, indicating that the final position is 80 m west of the initial position (pillar).
To calculate the total distance traveled, we need to consider the magnitudes of the individual displacements:
Total Distance = Distance in Segment 1 + Distance in Segment 2
= 200 m + 280 m
= 480 m
The total distance traveled is 480 m.
To learn more about Displacement click here
https://brainly.com/question/11934397
#SPJ11
. On a calm, sunny day, the air in the lowest inch or so of the atmosphere is heated primarily by ________.
a. convection
b. conduction
c. direct absorption of solar radiation
d. latent heat release
e. absorption of terrestrial radiation
On a calm, sunny day, the air in the lowest inch or so of the atmosphere is heated primarily by conduction. The other options are incorrect because the sun's radiation is absorbed by the ground, but the ground heats the air through conduction, not direct absorption. option b.
Latent heat release and absorption of terrestrial radiation are unrelated to this phenomenon. What happens on a calm, sunny day? On a calm, sunny day, the air in the lowest inch or so of the atmosphere is heated primarily by conduction. Heat is transmitted from the ground to the air through direct contact. Because the layer of air in contact with the ground is so small, the air heats up quickly, and its temperature rises. Convection is not a significant factor in this process because there is little vertical motion in the air mass closest to the ground.
to know more about conduction visit:
https://brainly.com/question/15085692
#SPJ11
A grinding wheel is a uniform cylinder with a radius of 8.65 cm and a mass of 0.350kg .
Calculate its moment of inertia about its center.
Calculate the applied torque needed to accelerate it from rest to 1900rpm in 6.00s if it is known to slow down from 1250rpm to rest in 54.0s .
A grinding wheel is a uniform cylinder with a radius of 8.65 cm and a mass of 0.350kg .
A) Its moment of inertia about its centre is [tex]1.37*10^-^3 Kg m^2[/tex].
B) The applied torque needed to accelerate it from rest to 1900rpm in 6.00s if it is known to slow down from 1250rpm to rest in 54.0s is [tex]4.87*10^-^2 mN[/tex].
a) To calculate the moment of inertia of the grinding wheel about its centre, we can use the formula for the moment of inertia:
[tex]I=1/2mr^2[/tex]
where:
I is the moment of inertia
m is the mass of the cylinder
r is the radius of the cylinder
Given:
Radius (r) = 8.65 cm = 0.0865 m
Mass (m) = 0.350 kg
Substituting these values into the formula:
[tex]I=1/2*0.350Kg*(0,0865m)^2\\I=1.37*10^-^3 Kgm^2[/tex]
Therefore, the moment of inertia of the grinding wheel about its center is approximately [tex]1.37*10^-^3Kgm^2[/tex].
b) The wheel slow down on its own from 1250 rpm to rest in 54.0s. To calculate the applied torque,
[tex]w[/tex]₀ =1250 rpm ×2π rad/60s =130.83 rad/s.
[tex]w[/tex] =0, Δt=54.0s.
α = [tex]w-w[/tex]₀/Δt
α = -2.42 rad/s²
τ = Iα = 1.37*10⁻³ *(-2.24) = -3.31*10⁻³ m N.
The net torque causing the angular acceleration is the applied torque plus the (negative) frictional torque.
τ = -3.31*10⁻³ m N.
[tex]w[/tex] = 1900 rpm* 2πrad/60 s = 198.86 rad/s.
α = [tex]w-w[/tex]₀/Δt = 198.86/6.0 = 33.14 rad/s².
∑τ = τapplied + τfri = 45.40*10⁻³ + 3.31*10⁻³
∑τ = 4.87*10⁻² m N.
Therefore, the applied torque needed to accelerate the grinding wheel from rest to 1900 rpm in 6.00 s is approximately 4.87*10⁻² m N.
T o know more about moment of inertia here
https://brainly.com/question/31439450
#SPJ4
the position of a 40 g oscillating mass is given by x(t)=(2.0cm)cos(10t) , where t is in seconds. determine the velocity at t=0.40s .
The velocity at t = 0.40s is approximately -(20 cm/s)sin(4). Note that the negative sign indicates the direction of the velocity.
To determine the velocity at t = 0.40s, we need to take the derivative of the position function with respect to time. Given that the position function is x(t) = (2.0 cm)cos(10t), we can find the velocity function by differentiating it.
The derivative of the cosine function is the negative sine function, and when multiplied by the derivative of the inside function (in this case, 10t), we obtain the chain rule. Therefore, the velocity function v(t) can be obtained as follows:
v(t) = dx/dt = d/dt[(2.0 cm)cos(10t)] = -(2.0 cm)(10)sin(10t)
Now, we can substitute t = 0.40s into the velocity function to find the velocity at that specific time:
v(0.40s) = -(2.0 cm)(10)sin(10 * 0.40) = -(20 cm/s)sin(4)
Thus, the velocity at t = 0.40s is approximately -(20 cm/s)sin(4). Note that the negative sign indicates the direction of the velocity.
To learn more about Velocity click here
https://brainly.com/question/30559316
#SPJ11
A 60-cm-diameter, 480 g beach ball is dropped with a 4.0mg ant riding on the top. The ball experiences air resistance, but the ant does not. Take rhoair =1.2 kg/m3. Part A What is the magnitude of the normal force exerted on the ant when the ball's speed is 2.0 m/s ? Express your answer with the appropriate units. Blocks with masses of 1.0 kg,3.0 kg, and 4.0 kg are lined up in a row on a frictionless table. All three are pushed forward by a 18 N force applied to the How much force does the 3.0 kg block exert on the 4.0 kg block? 1.0 kg block. Express your answer with the appropriate units. X Incorrect; Try Again; 5 attempts remaining Part B How much force does the 3.0 kg block exert on the 1.0 kg block?
Part A: To find the magnitude of the normal force exerted on the ant when the ball's speed is 2.0 m/s, we need to consider the forces acting on the ball.
The weight of the ball can be calculated as: Weight = mass * gravitational acceleration. Weight = 480 g * 9.8 m/s^2. Weight = 4.704 N. When the ball is falling with a speed of 2.0 m/s, the air resistance force acting on it will oppose its motion. The magnitude of the air resistance force can be calculated as: Air resistance = (1/2) * rho * A * v^2
where rho is the air density, A is the cross-sectional area of the ball, and v is its velocity. The cross-sectional area of the ball can be calculated as:
A = pi * r^2
A = pi * (30 cm)^2
A = 2827.43 cm^2
Converting the cross-sectional area to square meters:
A = 2827.43 cm^2 * (1 m/100 cm)^2
A = 0.2827 m^2
Substituting the values into the air resistance equation:
Air resistance = (1/2) * 1.2 kg/m^3 * 0.2827 m^2 * (2.0 m/s)^2
Air resistance = 0.6789 N
The net force acting on the ball can be calculated as the difference between the weight and the air resistance:
Net force = Weight - Air resistance
Net force = 4.704 N - 0.6789 N
Net force = 4.0251 N
Since the ball is not accelerating vertically (assuming it is in equilibrium), the magnitude of the normal force exerted on the ant is equal to the net force:
Magnitude of normal force = Net force
Magnitude of normal force = 4.0251 N
Therefore, the magnitude of the normal force exerted on the ant is 4.0251 N. Part B: To find the force exerted by the 3.0 kg block on the 4.0 kg block, we need to consider Newton's third law of motion, which states that for every action, there is an equal and opposite reaction. Since the 3.0 kg block is pushing the 4.0 kg block, the force exerted by the 3.0 kg block on the 4.0 kg block will be equal in magnitude but opposite in direction to the force exerted by the 4.0 kg block on the 3.0 kg block. Therefore, the force exerted by the 3.0 kg block on the 4.0 kg block is also 18 N. Part C: To find the force exerted by the 3.0 kg block on the 1.0 kg block, we apply the same principle of Newton's third law of motion. Since the 3.0 kg block is pushing the 1.0 kg block, the force exerted by the 3.0 kg block on the 1.0 kg block will be equal in magnitude but opposite in direction to the force exerted by the 1.0 kg block on the 3.0 kg block. Therefore, the force exerted by the 3.0 kg block on the 1.0 kg block is also 18 N.
To learn more about force, https://brainly.com/question/30507236
#SPJ11
A proton is placed in an electric field of intensity 700 N/C. What is the magnitude and direction of the acceleration of this proton due to this field?
A) 67.1×1010 m/s2 in the direction of the electric field
B) 6.71×1010 m/s2 in the direction of the electric field
C) 6.71×1010 m/s2 opposite to the electric field
D) 6.71×109 m/s2 opposite to the electric field
E) 67.1×1010 m/s2 opposite to the electric field
The magnitude and direction of the acceleration of the proton due to the electric field is 6.71×[tex]10^{10}[/tex] m/s² in the direction of the electric field for Electric field intensity (E) = 700 N/C. Option B is the correct answer.
We need to find the magnitude and direction of the acceleration of a proton in this electric field.
An electric field produces a force on a charged particle according to the equation F = qE, where F is the force, q is the charge of the particle, and E is the electric field intensity.
The charge of a proton is positive and equal to the elementary charge, q = +1.6 × [tex]10^{-19[/tex] C.
Substitute the values into the equation: F = (1.6 × [tex]10^{-19[/tex] C) × (700 N/C).
F = 1.12 × [tex]10^{-16[/tex] N
According to Newton's second law, F = ma, where m is the mass of the proton and a is its acceleration.
The mass of a proton is approximately 1.67 × [tex]10^{-27[/tex] kg.
Rearrange the equation to solve for acceleration: a = F/m.
a = (1.12 × [tex]10^{-16[/tex] N) / (1.67 × [tex]10^{-27[/tex] kg).
a = 6.71 × [tex]10^{10[/tex] m/s²
The magnitude of the acceleration is 6.71 × [tex]10^{10[/tex] m/s².
Since the proton has a positive charge, it experiences a force in the direction of the electric field. Therefore, the acceleration of the proton is also in the same direction.
Thus, the final answer is:
The magnitude of the acceleration of the proton is 6.71 × [tex]10^{10[/tex] m/s² in the direction of the electric field.
Learn more about the electric field intensity at
https://brainly.com/question/16869740
#SPJ4
A bag is filled with 100 red M&Ms, describe the mass as a mean and standard deviation. Please explain how to do so in excel. RED 0.751 0.841 0.856 0.799 0.966 0.859 0.857 0.942 0.873 0809 0.890 0.878 0.905 ORANGE YELLOW BROWN 0.735 0.883 0.696 0.895 0.769 0.876 0.865 0.859 0.855 0.864 0.784 0.806 0.852 0.824 0.840 0.866 0.858 0.868 0.859 0.848 0.859 0.838 0.851 0.982 0.863 0.888 0.925 0.793 0.977 0.850 0.830 0.856 0.842 0.778 0.786 0.853 0.864 0.873 0.880 0.882 0.931 BLUE 0.881 0.863 0.775 0.854 0.810 0.858 0.818 0.868 0.803 0.932 0842 0.832 0.807 0.841 0.932 0.833 0.881 0.818 0.864 0.825 0.855 0.942 0.825 0.869 0.912 0.887 0.886 GREEN 0.925 0.914 0.881 0.865 0.865 1.015 0.876 0.809 0.865 0.848 0.940 0.833 0.845 0.852 0.778 0.814 0.791 0.810 0.881 Mean Variance Red Orange Yellow Brown Blue Green 0.864 0.858 0.8345 0.848 0.856 0.864 0.003317 0.00251 0.001559 0.00632 0.001764 0.003245
In this case, the mean mass of the red M&Ms is approximately 0.864, and the standard deviation is approximately 0.003317.
To calculate the mean and standard deviation of the mass of the red M&Ms in Excel, you can follow these steps:
1. Enter the data into a column in Excel, starting from cell A1. Make sure the data is entered consistently in a single column.
2. To calculate the mean, use the formula "=AVERAGE(A1:A100)" in an empty cell, where A1:A100 is the range of cells containing the data. This formula calculates the average of the values in the specified range.
3. To calculate the standard deviation, use the formula "=STDEV(A1:A100)" in an empty cell, where A1:A100 is the range of cells containing the data. This formula calculates the standard deviation of the values in the specified range.
4. The mean and standard deviation will be displayed in the respective cells where you entered the formulas.
In this case, the mean mass of the red M&Ms is approximately 0.864, and the standard deviation is approximately 0.003317.
To learn more about standard deviation click here
https://brainly.com/question/13498201
#SPJ11
Satellite A has twice the mass of satellite B, and moves at the same orbital distance from Earth as satellite B. Compare the speeds of the two satellites.
a. The speed of B is one-half the speed of A.
b. The speed of B is twice the speed of A.
c. The speed of B is one-fourth the speed of A.
d. The speed of B is equal to the speed of A.
e. The speed of B is four times the speed of A.
The speed of satellite B is one-half the speed of satellite A.
The speed of a satellite in orbit is determined by the balance between the gravitational force acting on the satellite and the centripetal force required to keep it in circular motion. The centripetal force is given by the equation F = mv²/r, where m is the mass of the satellite, v is its velocity, and r is the orbital radius.
Given that satellite A has twice the mass of satellite B and both satellites are at the same orbital distance from Earth, the gravitational force acting on satellite A is twice that of satellite B. To maintain circular motion, the centripetal force required by satellite A is also twice that of satellite B.
Since the centripetal force is directly proportional to the velocity squared (F ∝ v²), in order for satellite A to have twice the centripetal force, it must have a velocity that is √2 times greater than satellite B. Therefore, the speed of satellite A is √2 times the speed of satellite B. Simplifying, we find that the speed of satellite B is one-half the speed of satellite A.
Hence, the correct answer is: a) The speed of B is one-half the speed of A.
Learn more about centripetal force here:
https://brainly.com/question/14021112
#SPJ11
Bands in uranus' atmosphere, similar to those seen on the other jovian planets,
a. True
b. False
The given statement "Bands in uranus' atmosphere, similar to those seen on the other jovian planets" is false.
Uranus, unlike the other Jovian planets (Jupiter and Saturn), does not exhibit distinct bands in its atmosphere. While Jupiter and Saturn have well-defined cloud bands caused by atmospheric circulation patterns, Uranus has a unique and less pronounced atmospheric structure.
Uranus is characterized by a feature known as the "hood," which is a region of elevated haze covering its poles, giving it a different appearance compared to the banded structure of Jupiter and Saturn.
The lack of prominent bands in Uranus' atmosphere is attributed to its unique axial tilt and its composition, which includes different types of ices.
These factors contribute to the distinct visual appearance of Uranus and differentiate it from the other Jovian planets.
To know more about jovian planets, refer here:
https://brainly.com/question/30874518#
#SPJ11
A mass moves back and forth in simple harmonic motion with amplitude A and period T.
(a) In terms of A, through what distance does the mass move in the time T?
(b) Through what distance does it move in the time 6.00T?
A mass moves back and forth in simple harmonic motion with amplitude A and period T.
(a) The mass moves a distance equal to the amplitude A.
(b) The time 6.00T, the mass moves a distance equal to 6A.
(a) In simple harmonic motion, the motion of an object repeats itself after one complete cycle, which corresponds to the period T. During one complete cycle, the mass moves back and forth, covering a total distance equal to the amplitude A.
Therefore, in the time T, the mass moves a distance equal to the amplitude A.
(b) If we consider a time of 6.00T, it corresponds to 6 complete cycles of the motion. Since each complete cycle covers a distance equal to the amplitude A, the mass will cover a total distance of 6A during this time.
Therefore, in the time 6.00T, the mass moves a distance equal to 6A.
To know more about simple harmonic motion here
https://brainly.com/question/28158580
#SPJ4
A vector a has components a x equals -5. 00 m in a y equals 9. 00 meters find the magnitude and the direction of the vector
A vector has two components: a magnitude and a direction. Magnitude is the length of the vector, and direction is the angle that the vector makes with the x-axis. We can use the Pythagorean theorem to find the magnitude of the vector a.Magnitude of vector a :
[tex]a = √(a_x² + a_y²)a_x = -5.00 ma_y = 9.00 m[/tex]
Substituting the values in the formula, we get;
[tex]a = √((-5.00 m)² + (9.00 m)²)a = √(25.00 m² + 81.00 m²)a = √1066 m²a = 32.7 m[/tex] (rounded to one decimal place)
Now, to find the direction of the vector, we can use trigonometry. The direction of the vector a is given by the angle that the vector makes with the positive x-axis. We can find this angle using the tangent function.
[tex]tan θ = a_y / a_xtan θ = (9.00 m) / (-5.00 m)θ = -60.3°[/tex] (rounded to one decimal place)The angle is negative because it is measured clockwise from the positive x-axis. Therefore, the magnitude of the vector a is 32.7 m, and the direction of the vector is 60.3° clockwise from the positive x-axis.
To know more about Pythagorean theorem visit :
https://brainly.com/question/14930619
#SPJ11
.As shown in (Figure 1), a layer of water covers a slab of material X in a beaker. A ray of light traveling upward follows the path indicated. Assume that θ1 = 45 ∘∘ and θ2= 69 ∘.
A. Using the information on the figure, find the index of refraction of material X.
B. Using the information on the figure, find the angle the light makes with the normal in the air .
The light makes an angle of 81.25° with the normal in the air and the index of refraction of material X will be 1.09. It is determined by Snell's Law.
What is Snell's Law?
Snell's law, also known as the law of refraction, describes the relationship between the angles of incidence and refraction when a wave, such as light, passes from one medium to another. It states:
n₁sin(θ₁) = n₂sin(θ₂),
As the refractive index of water is 1.33. The incidence angle from the image in the first case is 65°, while the refracted angle is 48°. Consequently, the medium X's refractive index will be,
nₓ= n_w*sin48/sin65= 1.09
The incident angle in the second scenario is 48°, and we must determine the refracted angle r for the air.
Since we now know that air has a refractive index of 1, so that the refracted angle is,
sin(r)= n_w* sin48= 0.988
r= sin⁻¹(0.988)= 81.25°
Hence, we can infer that the material X will have an index of refraction of 1.09 and that the angle the light makes with the normal in the air is 81.25° by applying Snell's Law.
To learn more about Snell's Law,
https://brainly.com/question/10112549
#SPJ4
Complete question:
As shown in (Figure 1), a layer of water covers a slab of material X in a beaker. A ray of light traveling upwards follows the path indicated.
a) Using the information on the figure, find the index of refraction of material X .
b) Find the angle the light makes with the normal in the air.
Young's modulus for bone is about Y = 1.6 × 1010 N/m2. The tibia (shin bone) of a man is 0.2 m long and has an average cross sectional area of 0.02 m2. What is the effective spring constant of the tibia in N/m?
The effective spring constant of the tibia is approximately 8.0 × 10^10 N/m.
Young's modulus (Y) represents the stiffness of a material and is defined as the ratio of stress to strain. In this case, we are given Y = 1.6 × 10^10 N/m^2.
To calculate the effective spring constant (k) of the tibia, we need to use Hooke's law, which states that stress (σ) is proportional to strain (ε), and the proportionality constant is Young's modulus (Y):
σ = Y * ε
The strain ε can be calculated as the change in length (ΔL) divided by the original length (L):
ε = ΔL / L
In this case, the original length (L) of the tibia is given as 0.2 m. We need to find the change in length (ΔL) in order to calculate the strain.
The average cross-sectional area (A) of the tibia is given as 0.02 m^2. We know that stress (σ) is force (F) divided by area (A):
σ = F / A
Since we are assuming the tibia acts as a spring, the force (F) can be calculated as F = k * ΔL, where k is the spring constant.
Combining these equations, we have:
F / A = Y * (ΔL / L)
Solving for ΔL:
ΔL = (F / A) * (L / Y)
Substituting the given values:
ΔL = (k * ΔL / A) * (L / Y)
Simplifying:
1 = (k / A) * (L / Y)
Rearranging to solve for k:
k = (A * Y) / L
Plugging in the values:
k = (0.02 m^2 * 1.6 × 10^10 N/m^2) / 0.2 m
k ≈ 8.0 × 10^10 N/m
Therefore, the effective spring constant of the tibia is approximately 8.0 × 10^10 N/m. This value represents the stiffness of the tibia, indicating how much force is required to deform it by a certain amount.
To know more about modulus visit :
https://brainly.com/question/30402322
#SPJ11
pluto differs significantly from the eight solar system planets in that (choose all that apply)
a. it is farther from the sun than any classical planet
b. it has a different composition than any classical planet
c. its orbit is chaotic
d. it is not round
e it has not cleared its orbit
Pluto differs significantly from the eight solar system planets in that it is farther from the sun than any classical planet, and it has not cleared its orbit.
Pluto's distance from the sun sets it apart from the other classical planets in our solar system. It resides in the outer regions of the solar system, where its average distance from the sun is much greater than that of any other planet. This vast distance means that Pluto receives significantly less sunlight and experiences much colder temperatures compared to the inner planets.
Additionally, Pluto has not cleared its orbit, which is a defining characteristic of the classical planets. The concept of clearing its orbit refers to a planet's ability to dominate its immediate surroundings gravitationally, removing or ejecting any smaller objects in its vicinity. Pluto's orbit intersects with the Kuiper Belt, a region populated by numerous small icy bodies, indicating that it has not achieved orbital dominance.
Pluto's unique characteristics and location in the solar system make it distinct from the classical planets. Its distant orbit and failure to clear its surroundings differentiate it from the eight planets.
Learn more about Solar system here:
https://brainly.com/question/32240766
#SPJ11
A 10-cm-diameter parallel-plate capacitor has a 1.0 mm spacing. The electric field between the plates is increasing at the rate of 1.5 x 10^6 V/ms.
A) What is the magnetic field strength on the axis?
B) What is the magnetic field strength of 3.0 cm from the axis?
C) What is the magnetic field strength of 6.7 cm from the axis?
A) On the axis: 2.0 μT B) 3.0 cm from the axis: 0.29 μT C) 6.7 cm from the axis: 0.13 μT
We can calculate the magnetic field strength using Ampere's Law, which states that the line integral of the magnetic field around a closed loop is proportional to the current passing through the loop.
The formula for the magnetic field strength on the axis of a parallel-plate capacitor is given by:
B = (μ₀ε₀I)/(2πr)
Where B is the magnetic field strength, μ₀ is the permeability of free space (4π × 10⁻⁷ T·m/A), ε₀ is the permittivity of free space (8.854 × 10⁻¹² C²/(N·m²)), I is the rate of change of electric flux, and r is the distance from the axis of the capacitor.
To find the rate of change of electric flux, we can use the formula:
I = ε₀A(dE/dt)
Where A is the area of the capacitor plates and dE/dt is the rate of change of electric field.
Given:
Diameter of the capacitor = 10 cm = 0.1 m
Radius of the capacitor = 0.05 m
Spacing between the plates = 1.0 mm = 0.001 m
Rate of change of electric field (dE/dt) = 1.5 × 10⁶ V/ms = 1.5 × 10³ V/s
A) On the axis:
The distance from the axis is equal to the radius of the capacitor plates (r = 0.05 m).
Substituting the given values into the formulas, we have:
A = πr²
= π(0.05 m)²
I = ε₀A(dE/dt)
= (8.854 × 10⁻¹² C²/(N·m²))(π(0.05 m)²)(1.5 × 10³ V/s)
B = (μ₀ε₀I)/(2πr) = (4π × 10⁻⁷ T·m/A)(8.854 × 10⁻¹² C²/(N·m²))(π(0.05 m)²)(1.5 × 10³ V/s) / (2π(0.05 m))
Calculating this expression gives us:
B = 2.0 μT
B) 3.0 cm from the axis:
The distance from the axis is r = 0.03 m.
Using the same formulas as before, we substitute the new value:
A = πr²
= π(0.03 m)²
I = ε₀A(dE/dt)
= (8.854 × 10⁻¹² C²/(N·m²))(π(0.03 m)²)(1.5 × 10³ V/s)
B = (μ₀ε₀I)/(2πr) = (4π × 10⁻⁷ T·m/A)(8.854 × 10⁻¹² C²/(N·m²))(π(0.03 m)²)(1.5 × 10³ V/s) / (2π(0.03 m))
Calculating this expression gives us:
B = 0.29 μT
C) 6.7 cm from the axis:
The distance from the axis is r = 0.067 m.
Using the same formulas as before, we substitute the new value:
A = πr²
= π(0.067 m)²
I = ε₀A(dE/dt)
= (8.854 × 10⁻¹² C²/(N·m²))(π(0.067 m)²)(1.5 × 10³ V/s)
B = (μ₀ε₀I)/(2πr)
= (4π × 10⁻⁷ T·m/A)(8.854 × 10⁻¹² C²/(N·m²))(π(0.067 m)²)(1.5 × 10³ V/s) / (2π(0.067 m))
Calculating this expression gives us:
B = 0.13 μT
The magnetic field strength on the axis of the parallel-plate capacitor is 2.0 μT. At a distance of 3.0 cm from the axis, the magnetic field strength is 0.29 μT, and at a distance of 6.7 cm from the axis, the magnetic field strength is 0.13 μT.
To know more about Magnetic Field visit:
https://brainly.com/question/14411049
#SPJ11
conduct a test to determine whether the second-order response surface is identical for each level of engine type.
To determine if the second-order response surface is identical for each level of engine type, a comparative test can be conducted.
In this test, multiple engines of different types (e.g., gasoline, diesel, electric) would be selected. Each engine type represents a different level. The test involves measuring and analyzing the response variables of interest, such as engine performance or emissions, while systematically varying input factors (e.g., throttle position, load). The goal is to assess if the response surface, which represents the relationship between input factors and the response variables, is consistent across different engine types. The test would involve conducting experiments using a design of experiments (DOE) approach. A suitable DOE method, such as factorial design or response surface methodology, would be employed. The input factors would be varied at different levels, and the corresponding response variables would be measured and recorded for each engine type.
To learn more about surface, Click here:
https://brainly.com/question/18991441
#SPJ11
A 72.5 g sample of a metal, initial temperature at 100.0 °C, is mixed with 200.0 mL of water, initially at 24.0 °C, in a calorimeter. The water/metal mixture reaches an equilibrium temperature of 26.8 °C. Calculate the specific heat of this metal.
A 72.5 g sample of a metal, initial temperature at 100.0 °C, is mixed with 200.0 mL of water, initially at 24.0 °C, in a calorimeter. The water/metal mixture reaches an equilibrium temperature of 26.8 °C. The specific heat of this metal is 11.53 J/g °C.
To calculate the specific heat of the metal, we can use the principle of energy conservation. The heat lost by the metal is equal to the heat gained by the water in the calorimeter.
The heat lost by the metal can be calculated using the formula:
[tex]Q_l_o_s_s[/tex] = m*c*ΔT
Where: [tex]Q_l_o_s_s[/tex] is the heat lost by the metal
m is the mass of the metal (72.5 g)
c is the specific heat of the metal (unknown)
ΔT is the change in temperature of the metal (26.8 °C - 100.0 °C)
The heat gained by the water can be calculated using the formula:
[tex]Q_g_a_i_n=m_w_a_t_e_r *c_w_a_t_e_r[/tex] * ΔT
Where: [tex]Q_g_a_i_n[/tex] is the heat gained by the water
[tex]m_w_a_t_e_r[/tex] is the mass of the water
[tex]c_w_a_t_e_r[/tex] is the specific heat of water (4.18 J/g °C)
ΔT is the change in temperature of the water (26.8 °C - 24.0 °C)
Since the heat lost by the metal is equal to the heat gained by the water, then:
m * c * ΔT = [tex]m_w_a_t_e_r *c_w_a_t_e_r[/tex]* ΔT
We can cancel out the ΔT terms:
m * c = [tex]m_w_a_t_e_r*c_w_a_t_e_r[/tex]
72.5 g * c = 200.0 g * 4.18 J/g °C
c = (200.0 g * 4.18 J/g° C) / 72.5 g
c ≈ 11.53 J/g °C
Therefore, the specific heat of the metal is approximately 11.56 J/g °C.
To know more about specific heat here
https://brainly.com/question/31608647
#SPJ4
two resistors in series are equivalent to 9.0 ω, and in parallel they are equivalent to 2.0 ω. what are the resistances of these two resistors?
The equivalent resistance of two resistors is 9.0 when they are connected in series, and 2.0 when they are connected in parallel. The resistance of the first resistor (R1) is 6.0, while the resistance of the second resistor (R2) is 3.0, as determined by solving the system of equations.
Let's denote the resistances of the two resistors as R₁ and R₂.
According to the given information:
1. When the two resistors are in series, their equivalent resistance is 9.0 Ω. In series, the equivalent resistance is the sum of individual resistances.
So, R₁ + R₂ = 9.0 Ω.
2. When the two resistors are in parallel, their equivalent resistance is 2.0 Ω. In parallel, the reciprocal of the equivalent resistance is equal to the sum of the reciprocals of individual resistances.
So ,[tex]\frac{1}{R_1} + \frac{1}{R_2} = \frac{1}{2.0 \, \Omega}[/tex]
We have a system of equations:
R₁ + R₂ = 9.0 Ω (Equation 1)
[tex]\frac{1}{R_1} + \frac{1}{R_2} = \frac{1}{2.0 \, \Omega}[/tex] (Equation 2)
To solve this system, we can rearrange Equation 2 to get:
[tex]\frac{{R_1 + R_2}}{{R_1 \cdot R_2}} = \frac{1}{{2.0 \, \Omega}}[/tex]
R₁ * R₂ = 2.0 * (R₁ + R₂) (Equation 3)
Now, we can substitute Equation 1 into Equation 3:
R₁ * R₂ = 2.0 * 9.0 Ω
R₁ * R₂ = 18.0 Ω (Equation 4)
We have a quadratic equation in terms of R₁ and R₂. To solve it, we can use various methods such as factoring, quadratic formula, or numerical approximation.
By inspection, we can find that one possible solution is R₁ = 6.0 Ω and R₂ = 3.0 Ω, which satisfies both Equation 1 and Equation 4.
Therefore, the resistance of the first resistor (R₁) is 6.0 Ω, and the resistance of the second resistor (R₂) is 3.0 Ω.
To know more about the equivalent resistance refer here :
https://brainly.com/question/31788815#
#SPJ11
A solid disk with a radius R rotates at a constant rate ω. Which of the following points has the greater angular displacement ?
The point on the circumference of the solid disk that is farther away from the center has a greater angular displacement.
The angular displacement of a point on a rotating object is determined by the distance traveled along the circumference of the object. Since the disk rotates at a constant rate ω, all points on the disk will have the same angular velocity. However, points farther away from the center of the disk have a greater linear velocity because they have to cover a larger distance in the same amount of time.
Consider two points on the disk: one near the center and one near the circumference. The point near the center has a smaller radius, and thus it covers a shorter distance along the circumference compared to the point near the circumference, which has a larger radius. Therefore, in the same amount of time, the point near the circumference covers a greater angular distance along the circumference, resulting in a greater angular displacement.
In conclusion, the point on the circumference of the solid disk that is farther away from the center has a greater angular displacement because it covers a greater distance along the circumference in the same amount of time.
To learn more about angular displacement refer:
https://brainly.com/question/31327129
#SPJ11
Green light of wavelength 540 nm is incident on two slits that are separated by 0.60mm .
Determine the frequency of the light.
f =
Determine the angles of the first two maxima of the interference pattern.
theta=
The frequency of the green light is approximately [tex]5.56 * 10^{14} Hz.[/tex] The angle of the first maximum is approximately 52.8°. The angle of the second maximum is approximately 105.6°.
To determine the frequency of the light, we can use the relationship between frequency (f), speed of light (c), and wavelength (λ): c = f * λ
where:
c = speed of light = [tex]3.00 * 10^8 m/s[/tex] (approximately)
λ = wavelength
Given that the wavelength of the green light is 540 nm, we need to convert it to meters:
λ = 540 nm
[tex]= 540 * 10^{-9} m[/tex]
Now we can rearrange the equation to solve for frequency:
f = c / λ
Substituting the values:
[tex]f = (3.00 * 10^8 m/s) / (540 * 10^{-9} m)\\f = 5.56 * 10^{14} Hz[/tex]
Therefore, the frequency of the green light is approximately [tex]5.56 * 10^{14} Hz.[/tex]
Now let's determine the angles of the first two maxima of the interference pattern. For a double-slit interference pattern, the angles of the maxima are given by the equation:
sin(θ) = mλ / d
where:
θ = angle of the maxima
m = order of the maxima (m = 0 for the central maximum)
λ = wavelength
d = separation between the slits
For the first maximum (m = 1), we can rearrange the equation to solve for θ:
θ = arcsin(mλ / d)
Substituting the values:
θ = arcsin[tex]((1)(540* 10^{-9} m) / (0.60 * 10^{-3} m))[/tex]
θ ≈ 0.920 radians (approximately)
To convert this to degrees:
θ ≈ 0.920 radians * (180/π) ≈ 52.8° (approximately)
Therefore, the angle of the first maximum is approximately 52.8°.
For the second maximum (m = 2), we can use the same equation:
θ = arcsin [tex]((2)(540 * 10^{-9} m) / (0.60 * 10^{-3} m))[/tex]
θ ≈ 1.84 radians (approximately)
Converting to degrees:
θ ≈ 1.84 radians * (180/π) ≈ 105.6° (approximately)
Therefore, the angle of the second maximum is approximately 105.6°.
To learn more about wavelength visit:
brainly.com/question/14761341
#SPJ11
15. A pendulum consisting of a sphere suspended from a light string is oscillating with a small angle with respect to the vertical. The sphere is then replaced with a new sphere of the same size but greater density and is set into oscillation with the same angle. How do the period, maximum kinetic energy, and maximum acceleration of the new pendulum compare to those of the original pendulum?
Maximum Maximum Period Kinetic Energy Acceleration
(A) Larger Larger Smaller (B) Smaller Larger Smaller
(C) The same The same The same
(D) The same Larger The same
The period, maximum kinetic energy, and maximum acceleration of the pendulum will be the same as those of the original pendulum when the size and angle of oscillation are kept constant. So the answer is option C.
When comparing the period, maximum kinetic energy, and maximum acceleration of the new pendulum with the original pendulum, we can analyze the effects of changing the density of the sphere while keeping the size and angle of oscillation the same.
Period:
The period of a simple pendulum is given by the formula:
T = 2π√(L/g)
Where T is the period, L is the length of the pendulum, and g is the acceleration due to gravity. The period depends only on the length of the pendulum and the acceleration due to gravity, and it is independent of the mass or density of the pendulum.
Since the size and angle of oscillation remain the same when the sphere is replaced, the length of the pendulum remains unchanged. Therefore, the period of the new pendulum will be the same as the original pendulum.
Maximum Kinetic Energy:
The maximum kinetic energy of a simple pendulum is given by the formula:
K_max = (1/2) m v_max^2
Where K_max is the maximum kinetic energy, m is the mass of the pendulum, and v_max is the maximum velocity of the pendulum bob.
When the sphere is replaced with a new sphere of greater density, the mass of the pendulum increases. However, the maximum velocity depends on the amplitude (angle) of oscillation and is not affected by the mass or density.
Since the amplitude remains the same, the maximum velocity and, consequently, the maximum kinetic energy will be the same for the new pendulum as for the original pendulum.
Maximum Acceleration:
The maximum acceleration of a simple pendulum is given by the formula:
a_max = gθ
Where a_max is the maximum acceleration, g is the acceleration due to gravity, and θ is the amplitude (angle) of oscillation.
The maximum acceleration depends on the amplitude and acceleration due to gravity. Since the amplitude remains the same and the acceleration due to gravity is constant, the maximum acceleration will be the same for the new pendulum as for the original pendulum.
The period, maximum kinetic energy, and maximum acceleration of the new pendulum will be the same as those of the original pendulum when the size and angle of oscillation are kept constant. Therefore, the correct option is (C) The same, The same, The same.
To learn more about pendulum, visit
https://brainly.com/question/29702798
#SPJ11
The shortest wavelength of visible light is approximately 400 nm. Express this wavelength in centimeters. a. 4 x 10^-5 cm b. 4 x 10^-7 cm c. 4 x 10^-9 cm d. 400 x 10^-11 cm e. 4 x 10^-11 cm
The shortest wavelength of visible light, approximately 400 nm, can be expressed as [tex]4 *10^-^5[/tex] cm.
Visible light consists of electromagnetic waves with different wavelengths. Wavelength is the distance between successive peaks or troughs of a wave. In the electromagnetic spectrum, visible light has a range of wavelengths, with violet light having the shortest wavelength and red light having the longest. The given wavelength of 400 nm corresponds to the violet end of the visible light spectrum.
To convert this wavelength to centimeters, we need to use the conversion factor: [tex]1 nm = 10^-^7 cm[/tex]. By substituting the given wavelength into the conversion factor, we can calculate the wavelength in centimeters.
[tex]400 nm * (1 cm / 10^-^7 nm) = 400 * 10^-^7 cm = 4 * 10^-^5 cm[/tex].
Therefore, the correct option is a. [tex]4 *10^-^5[/tex], which represents the shortest wavelength of visible light.
Learn more about electromagnetic spectrum here:
https://brainly.com/question/30415893
#SPJ11
kepler’s third law says that a comet with a period of 160 years will have a semimajor axis of
Kepler's third law states that the square of a planet's orbital period is proportional to the cube of its semimajor axis.
According to Kepler's third law, the square of a planet's orbital period is directly proportional to the cube of its semimajor axis. The formula can be expressed as T^2 = ka^3, where T is the orbital period, a is the semimajor axis, and k is a constant. By rearranging the formula, we can solve for the semimajor axis.
In this case, the comet has a period of 160 years. Let's assume that the orbital period is measured in Earth years. Therefore, T = 160 years. Substituting these values into the formula, we get 160^2 = ka^3. Since k is a constant, we can solve for a by taking the cube root of both sides: a = (160^2)^(1/3).
Evaluating this expression, we find that the semimajor axis of the comet is approximately 36.5 astronomical units (AU). Therefore, a comet with a period of 160 years will have a semimajor axis of approximately 36.5 AU.
Learn more about Kepler's third law here:
https://brainly.com/question/30404084
#SPJ11
Find the fuel efficiency in units of miles per gallon (mpg) if the vehicle’s fuel sensor measures a mean fuel consumption rate of 4 gallons per hour, and the speedometer measures a mean speed of 83 mph. Round to 1 d.p.
The fuel efficiency, rounded to 1 decimal place, is approximately 20.8 miles per gallon (mpg).
To find the fuel efficiency in miles per gallon (mpg), we need to calculate the distance traveled per gallon of fuel.
In this case:
Mean fuel consumption rate = 4 gallons per hour
Mean speed = 83 mph
To find the distance traveled per gallon, we can divide the mean speed by the fuel consumption rate:
Distance per gallon = Mean speed / Fuel consumption rate
Distance per gallon = 83 miles / 4 gallons
Distance per gallon ≈ 20.8 miles per gallon
Therefore, the fuel efficiency = 20.8 miles per gallon (mpg).
Learn more about fuel efficiency here:
https://brainly.com/question/27021605
#SPJ11
after three half-lives of an isotope, 1 billion (one-eighth) of the original isotope’s atoms remain. how many atoms of the daughter product would you expect to be present?
Approximately 7/8 of the daughter product's initial number of atoms should still be present after three half-lives.
To determine the number of atoms of the daughter product present after three half-lives of an isotope, we can use the concept of radioactive decay.
Each half-life of a radioactive isotope is the time it takes for half of the initial parent atoms to decay into daughter atoms. After three half-lives, the remaining fraction of parent atoms can be calculated as follows:
Remaining fraction = (1/2)^(number of half-lives)
In this case, the remaining fraction is given as 1 billion (one-eighth) of the original isotope's atoms. Let's calculate the remaining fraction:
1/8 = (1/2)³
Now, we can solve for the number of atoms of the daughter product remaining:
Remaining atoms of daughter product = Initial atoms of parent isotope - Remaining atoms of the parent isotope
Let's assume the initial number of parent atoms is N:
Remaining atoms of daughter product = N - N * Remaining fraction
Substituting the calculated remaining fraction of 1/8, we have:
Remaining atoms of daughter product = N - N * (1/8)
Simplifying further:
Remaining atoms of daughter product = N * (1 - 1/8)
Remaining atoms of daughter product = N * (7/8)
Therefore, after three half-lives, we would expect approximately 7/8 of the original number of atoms of the daughter product to be present.
To learn more about isotopes click:
brainly.com/question/20596678
#SPJ4
A mirror produces an image that is inverted and twice as tall as the object. If the image is 60 cm from the mirror, what is the radius of curvature of the mirror?
a. -40 cm
b. +80 cm
c. None of the choices are correct.
d. +40 cm
e. -80 cm
The radius of curvature of the mirror is -80 cm. The correct option is option (e).
Image produced by the mirror is inverted and twice as tall as the object.
Image distance, v = -60 cm
Magnification, m = -2
The mirror formula,
1/v + 1/u = 1/f
Substituting the values,
1/-60 + 1/u = 1/f......(1)
Magnification is ,
m = -v/u
= -2u
= v/m
= -60/-2
= 30 cm
Substituting this value in... (1),
1/-60 + 1/30 = 1/f
Solving this equation, we get,
f = -40 cm
R = 2f
Therefore, the radius of curvature of the mirror is -80 cm.
Learn more about the radius of curvature:
brainly.com/question/30105927
#SPJ11