A torque of 36.5 N · m is applied to an initially motionless wheel which rotates around a fixed axis. This torque is the result of a directed force combined with a friction force. As a result of the applied torque the angular speed of the wheel increases from 0 to 10.3 rad/s. After 6.10 s the directed force is removed, and the wheel comes to rest 60.6 s later.
(a) What is the wheel's moment of inertia (in kg m2)? kg m
(b) What is the magnitude of the torque caused by friction (in N m)? N m
(c) From the time the directed force is initially applied, how many revolutions does the wheel go through?
______ revolutions

(1) Relief valves are components used in pneumatic systems to prevent harm. (2) Pneumatic and hydraulic systems both employ check valves. A- Both Nos. 1 and 2 are accurate in relation to the aforementioned assertions.

Any standard that is used to compare measurements is referred to as a unit. Measurements of a property that have been taken using various units—for example, inches to centimeters—can be accommodated using unit conversions.

The metric system, sometimes referred to as the SI, is the accepted unit of measurement on a global scale. World Metrology Day is an international holiday commemorating the signing of the International Treaty of the Meter in Paris on May 20, 1875, by seventeen nations, including the United States.

To know more about Units visit:

https://brainly.in/question/11622331

#SPJ4

It refers to a quantity changed by the experimenter.

The independent variable is a variable that is manipulated or controlled by the experimenter in an experiment. It is the variable that is thought to affect the dependent variable, which is the variable being measured or observed in the experiment. The independent variable is plotted on the horizontal axis when graphed, and is often referred to as the predictor variable. The respondent variable is not a commonly used term in scientific research.

The applied force must be larger than the frictional force for a body to move successfully.

Between two surfaces that are sliding or attempting to slide over one another, there is a force called friction. For instance, friction makes it challenging to push a book down the floor. Friction always moves an object in a direction that is counter to the direction that it is traveling or attempting to move.

When a body is pushed, an exact quantity of frictional force is created, up until the point where Fs max = coefficient of friction * normal force.

After that, when fs max exceeds the frictional force, dynamic friction enters the picture, which is what causes the body to move.

The body begins to move after a force is applied that is more than the minimal need, or what we refer to as the Threshold (f applied > fs max).

In the case of a frictionless surface, the applied force will be perpendicular to the gravitational force that is being taken into account. Even the slightest acceleration must cause the body to move.

To know more about friction:

https://brainly.com/question/28356847

#SPJ4

I2 = V / R2 = 0.678 A ; I3 = V / R3 = 0.678 A are the current flows in R2 and R3.

Here R1 = R2 = R3 = R4 = 4.43Ω

And E = 9.01 V

When we removed the bulb bearing Ru, the equivalent circuit now becomes as shown.

Now R2 and R3 are in parallel, so their equivalent resistance

 1/Rp = 1/R2 + 1/R3

 Rp = 2.215 Ω

Again, R1 is connected Rp in series so equivalent resistance

R = R1 + Rp = 6.645 Ω

Current through ‘R1’ is

 I1 = V / R = 9.01 / 6.645 = 1.356 A

Potential across R2 and R3 is

 V = E – I1R1 = 3.0033V

So current through R2

  I2 = V / R2 = 0.678 A

Current through R3

 I3 = V / R3 = 0.678 A

To learn more about Electrical Circuits:

https://brainly.com/question/2969220

#SPJ4

Answer:

The fuse in a plug is a safety device designed to protect the lead rather than the appliance. It is a deliberate weak link in a circuit which will 'blow' if an electrical appliance or extension lead draws too much current due to either an overload or a fault.

The ecosystem that is present in the northern hemisphere is Tindouf

Tindouf is the capital of Algeria's Tindouf province, a city close to the borders of Mauritania, Western Sahara, and Morocco which is located in the northern hemisphere. From the chromatogram drawn by Teresa Glass, we concluded that the city of Tindouf, Algeria is a desert biome with very low winter precipitation and high temperatures. This region is of strategic importance. It has an Algerian military base and airport, with regular flights to Algiers and other domestic destinations. Garet Djebilet's settlement is located in his Tindouf municipality near the border with Mauritania. The settlement has an iron mine and an abandoned airport, and is located about 70 kilometers northwest of Awinetbel his Egla.

Learn more about the northern hemisphere in

https://brainly.com/question/13661560

#SPJ4

Explanation:

To find the y-component of a vector that is 14.4 m long and points in a 133 degree direction, you can use the trigonometric functions sine and cosine.

The y-component of a vector is given by the product of the vector's length and the sine of the angle between the vector and the positive x-axis. The x-component of a vector is given by the product of the vector's length and the cosine of the angle between the vector and the positive x-axis.

You can find the y-component of the vector by using the formula:

y-component = vector length * sine(angle)

In this case, the vector length is 14.4 m, and the angle between the vector and the positive x-axis is 133 degrees. You can find the y-component of the vector by plugging these values into the formula:

y-component = 14.4 m * sine(133 degrees)

You can use a calculator or look up the value of sine(133 degrees) in a table to find the y-component of the vector. You will find that the y-component of the vector is approximately -11.9 m.

Note that the y-component of the vector is negative because the vector points in a direction that is below the positive x-axis. The x-component of the vector would be positive because the vector points in a direction that is to the right of the y-axis.

Use the trigonometric functions sine and cosine to determine the y-component of a vector that is 14.4 m long and points in a 133 degree direction.

A vector's y-component is calculated by multiplying its length by the sine of the angle it makes with the positive x-axis. A vector's x-component is calculated by multiplying its length by the cosine of the angle it makes with the positive x-axis.

Utilizing the following formula, you can get the vector's y-component: y-component = sine * vector length (angle).

The vector length in this instance is 14.4 m, and the angle it makes with the positive x-axis is 133 degrees. the location of the y-component.

To learn more about vector, refer to the link:

https://brainly.com/question/24256726

#SPJ2

The required  speed of the center of mass of the two-car system is 10 m/s.

Option(2) is corret.

The reason is simple. Velocity is the percentage of time an object moves along a path, and Velocity is the speed and direction of an object's movement.

The mathematical calculation of velocity is relatively simple, the average velocity of an object is calculated by dividing the distance traveled by the time it took the object to travel that distance. Velocity, on the other hand, is mathematically complex and can be calculated in different ways depending on what information is available about the object's motion. In its simplest form, the average velocity is calculated by dividing the change in position (Δr) by the change in time (Δt).

Let the mass of cars which is same is M,

Speed (V1) = 30 m/s

Speed (V2) = -10 m/s

Then,

Speed of center of mass = MV1 + MV2/2M

Speed of center of mass = M(30) + M(-10)/2M

Speed of center of mass = 30M - 10M/2M

Speed of center of mass = 20M/2m

Speed of center of mass = 10 m/s

Thus, Speed of center of mass is 10 m/s

To know more about Speed, visit:

brainly.com/question/13943409

#SPJ4

A nova or supernova may be the most catastrophic occurrence in all of nature.

A negatively charged subatomic particle called an electron can either be free or attached to an atom (not bound). One of the three main types of particles in an atom is an electron that is attached to it; the other two are protons and neutrons.

For creating cross-platform desktop apps using HTML, CSS, and JavaScript, GitHub developed the open source library called Electron. Chromium and Node are combined to create Electron, which does this. Apps may be produced for Mac, Windows, and Linux and combined with JavaScript into a single runtime.

To know more about Electrons visit:

https://brainly.com/question/1255220

#SPJ4

The title has the incorrect order for the variables.

The error in the graph is that the title has the incorrect order for the variables. Therefore, option D is correct.

Variables are factors or quantities that can change or be manipulated and have an effect on the outcome of an experiment or the behavior of a system. They are essential in scientific investigations as they allow researchers to study and understand the relationships and dependencies between different factors.

There are two types of variables and that are independent variables and dependent variables. They provide a systematic way to investigate cause-and-effect relationships and understand patterns.

Learn more about variables, here:

https://brainly.com/question/15078630

#SPJ6

Answer:

Answer:

let the first point be a second be b third be c fourth be d and last point be e.

The point a and d are incorrect. because tye plotting of the is incorrect

The statement "the speed of light is always the same no matter how fast you are moving" is true. This phenomenon is known as the constancy of the speed of light.

According to the theory of relativity, the speed of light in a vacuum is a constant value that is independent of the motion of the observer. This means that no matter how fast you are moving, you will always measure the speed of light to be the same value.

This idea may seem strange and counterintuitive, but it has been experimentally verified and is now a fundamental principle of modern physics. It has important consequences for our understanding of the nature of space and time, and it has played a key role in the development of many important scientific theories, including the theory of relativity.

To know more about relativity

https://brainly.com/question/29258869

#SPJ4

The time interval during which the speed of the wheel is increasing is 4 s.

Angular acceleration is the term used to describe the temporal pace at which angular velocity varies. Radians per square second is used as the measurement unit.

At time t = 0, the angular velocity is ω₁ = - 6.00 rad/s.

At time t = 10.0 s, the angular velocity is ω₂ = +4.00 rad/s.

Angular acceleration of the wheel can be written as= change in angular velocity /time interval

= ( 4.00 - (-6.00))/10 rad/s²

= 1.0 rad/s²

Hence, angular velocity becomes zero at time = ( 0 - ( -6))/1.0 s = 6 s.

So, during t = 0 to t = 6s, the clockwise angular  velocity of the wheel decreases from 6.00 rad/s to 0.00 rad/s and  during t = 6s to t = 10s , the counterclockwise angular  velocity of the wheel increases from 0.00 rad/s to +4.00 rad/s.

Hence,  the time interval during which the speed of the wheel is increasing is = 10 s - 6 s = 4 s.

Learn more about angular acceleration here:

https://brainly.com/question/29428475

#SPJ1

The highest possible The value of a graph, also known as the global maximum, is the location where the graph's y value achieves its absolute maximum.

To determine the critical point, we shall set the function's first derivative to zero and solve for x. This point's maximum or minimum value can be determined by taking the second derivative, or f”(x). The second derivative will have a minimal value if it is positive.

The two blocks are thought to be in a balance. If we force P to go to £2.69, then there is no maximum value and one piece equals zero. Zero is less than that, hence the system ought to be in equilibrium. If the force p is in at £2.69, then it must be of equal brands. When everyone is balanced.

Therefore, The maximum value for the entire function is at this point. The location on a graph where the y-coordinate has the lowest value is known as the minimal value.

Learn more about plot here:

https://brainly.com/question/29172804

#SPJ1

Yes, the range would change. Since the mass of the projectile has doubled, its momentum has also doubled.

Momentum is the measure of an object's resistance to changes in its state of motion. It is a vector quantity, meaning it has both magnitude and direction. Momentum is calculated by multiplying the mass and velocity of an object. Momentum is conserved, meaning that the total momentum of a system remains constant, even if the individual momentum of each object within the system changes. In a collision between two objects, the total momentum before the collision is equal to the total momentum after the collision. Momentum is a powerful concept and has many applications in physics. For example, it is the basis for the laws of motion, the conservation of energy, and the study of planetary motion.

Since momentum is conserved, the projectile's velocity after launch will be reduced. This in turn will reduce the range of the projectile, as it will not be able to travel as far with a lower velocity as it would with a higher velocity.

To learn more about momentum
https://brainly.com/question/18798405
#SPJ4

This range would increase 4 times.

What does the term "projectile motion" refer to?

The movement of an object that has been launched into the air is known as projectile motion. Only gravity is felt by the item after the initial force that launches it. Projectile and trajectory both refer to the same thing: an object.

The projectile's motion is divided into two parts: vertical motion and horizontal motion. Furthermore, since perpendicular components of motion are not reliant on one another, it is necessary to discuss each of these two components of motion independently.

Range of projectile is  R=(vi²sin2∅)/g

So when the velocity is doubled, Range R will be

I.e R'= ((2Vi)²sin2∅)/g

R'=4(Vi²sin2∅)/g

R'=4R

To learn more about projectile motion use link below:

https://brainly.com/question/10680035

#SPJ4

A field line is drawn at a location that is perpendicular to the net. Therefore, the tangent to the electric field line at any place coincides with the direction of the electric field there.

Each field line has a direction written on it with an arrow, just like gravitational field lines do. This direction indicates the direction of the electric field at all places along the field line. The density of the field lines represents the relative field strength.

Electric field is a vector quantity, hence a vector arrow can be used to depict it. The length of the arrows at any particular position is inversely proportional to the strength of the electric field there, and they all point in that direction.

To know more about electric field lines visit:-

https://brainly.com/question/14438235

#SPJ4

(a) The gas moves from point a to point b in an isochoric process in which the volume stays constant.

The work done when the gas moves from point A to point B is Wab = PV = 0.

The labor involved in getting the gas to boil, Wbc = PV = 1.4. (9.3 - 5.9) L.atm = 4.76 1 L.atm is equal to 101.325 J.

Work completed, ∆W = 101.325 × 4.76 = 482.3 J

Therefore, the process' overall work was a, b, and c.

Wtotal = 0 plus 482.3 J = 482.3 J (Ans) (Ans)

(b) As previously stated, point C is where the gas temperature returns to its initial value.

As a result, in the process ac through b, the gas doesn't undergo any temperature change.

Tfinal = Tinitial

Therefore, internal energy change U = 0.

To know more about Constant volume visit:

https://brainly.in/question/49693981

#SPJ4

The resistance of the wire, given that it is connected to a 9.0 V power pack and an ammeter is 36 ohms

From Ohm's law, we understood that the voltage, current and resistance are related according to the following formula:

Voltage (V) = Current (I) × resistance (R)

V = IR

Using the above formula, we can obtain the resistance of the wire as follow:

Voltage (V) = Current (I) × resistance (R)

9 = 0.25 × resistance

Divide both sides by

Resistance = 9 / 0.25

Resistance = 36 ohms

Thus, we can conclude that the resistance of the wire is 36 ohms

Learn more about resistance:

https://brainly.com/question/23960560

#SPJ1

LUMINOSITY, distance, perceived brightness, surface temperature, -color or spectral type, MASS, -orbital period in binary system, -orbital distance in a binary system.

In physics, mass is a quantitative measure of inertia, a basic characteristic of all matter. It is essentially the resistance a body of matter gives to a change in its speed or location as a result of the application of a force.

A measurement of the volume of material that makes up or is contained within a physical body. Newton's laws of motion are based on classical mechanics, which relates an object's mass to the force needed to accelerate it and, consequently, to its inertia.

To know more about Mass visit:

https://brainly.com/question/28221042

#SPJ4

The correct statement about the direction of  transfer of energy  in an isolated system is b) In an isolated system, energy always transfers from a warmer region to a cooler region .So, correct option is b.

An isolated system is a thermodynamic framework that can't trade either energy or matter beyond the framework. There are two manners by which this might happen: The framework might be so far off from another framework that it can't associate with them. The framework might be encased to such an extent that neither energy nor mass might enter or exit.

When temperature remains constant then energy transfer takes place between different components of system will be possible.Since temperature is different ,energy flow is favored from the warmer region to colder region because of difference in temperature.

Hence, correct option is b.

To know more about isolated system, visit here:

https://brainly.com/question/13176875

#SPJ4

(Complete question) is:

Which one of the statements below describes the direction of thermal energy transfer in an isolated system?

a)In an isolated system, for energy transfer to take place the entire system must remain at a constant temperature.

b)In an isolated system, energy always transfers from a warmer region to a cooler region

c)In an isolated system, energy always transfers from cooler region to a warmer region

d)In an isolated system, no transfer of energy between regions of the system can take place.

e)In an isolated system, energy cannot be transferred from a hotter region to a colder region.

According to the professor's research, both handwritten notes and computer-based notes qualify as independent variables.

The professor's study considers handwritten notes and computer-based notes to be independent variables. These other qualities will be examined to see if they change depending on note-taking technique, including better memory and exam recall.

What kinds of variables are the groupings for taking notes?

Because they are being examined for their potential to influence other factors, the note-taking groups that use handwritten and computerised notes are regarded as independent variables.

Better exam memory and recall are those other variables, and their changes in response to note-taking methodology will be investigated.

To know more about independent variables, visit:

https://brainly.com/question/28871343

#SPJ1

The fringe separation of the double-slit interference is 0.884 mm.

When two coherent light waves from separate sources collide, the energy distribution caused by the first wave is altered by the second. The term "interference of light" refers to this alteration in the distribution of light energy brought on by the superposition of two light waves.

Wavelength of light: λ = 680 nm = 680 × 10⁻⁹ m.

Separation between the two slits: d = 0.1 mm = 0.1 × 10⁻³ m.

Screen distance: D = 1.3 m.

Hence, the fringe separation: x = λD/d

= ( 680 × 10⁻⁹)×(1.3 )/(0.1 × 10⁻³ ) m

= 0.000884 m

= 0.884 mm.

Learn more about interference here:

https://brainly.com/question/16098226

#SPJ1

Answer: 13 m/s.

Explanation: To solve this problem, we need to use the equation for motion with constant acceleration:

d = v₀t + 1/2 at²

where d is the distance traveled, v₀ is the initial velocity, t is the time it takes to travel that distance, and a is the acceleration.

Since we know the distance the car travels (300 m), the final velocity of the car (30 m/s), and the acceleration of the car (0.75 m/s²), we can solve for the initial velocity. We just need to rearrange the equation to solve for v₀:

v₀ = (d - 1/2 at²) / t

In this case, we can plug in the known values to find the initial velocity:

v₀ = (300 - 1/2 * 0.75 * t²) / t

Since the final velocity of the car is 30 m/s and the acceleration is 0.75 m/s², we can use the equation for motion with constant acceleration to find the time it takes for the car to travel 300 m:

v = v₀ + at

30 = v₀ + 0.75t

Rearranging to solve for t, we get:

t = (30 - v₀) / 0.75

Substituting this value for t in the equation for the initial velocity, we get:

v₀ = (300 - 1/2 * 0.75 * ((30 - v₀) / 0.75)²) / ((30 - v₀) / 0.75)

This simplifies to:

v₀ = (300 - 1/2 * 0.75 * (900 - 2v₀) / 0.75) / (30 - v₀)

which simplifies further to:

v₀ = (300 - 675 + v₀) / (30 - v₀)

Solving for v₀, we get:

v₀ = -375 / -29

which simplifies to:

v₀ = 13 m/s

Therefore, the initial velocity of the car is 13 m/s.

When there is compression of 3.63 cm in the spring , block will have maximum velocity. there after its speed will start decreasing.

What is potential energy of a spring?

When spring is stretched, it undergoes displacement. It comes to its equilibrium position when force is removed. So, it exerts an equal and opposite force When it is stretched. Work is done by this force that is stored in the form of potential energy.

Since potential energy = force × displacement

and, force = spring constant × displacement

So, potential energy = spring constant × (displacement)²

According to the given question:

a ) work done by gravitational force

= mg sinθ ( d + .21)

Potential energy stored in compressed spring

= 1/2 k x²

= .5 x 431 x ( .21 )²

= 9.5

According to conservation of energy

mg sinθ ( d + .21)  = 9.5

3.2 x 9.8 x sin 30( d + .21 ) = 9.5

d = 40 cm

b )

As long as mg sin30 is greater than kx ( restoring force ) , there will be acceleration in the block.

mg sin30 = kx

3.2 x 9.8 x .5 = 431 x

x =  3.63 cm

When there is compression of 3.63 cm in the spring , block will have maximum velocity. there after its speed will start decreasing.

Complete question:

A 3.20 kg block starts at rest and slides a distance d down a frictionless β = 30.0 ◦ incline, where it runs into a spring with spring constant k = 431 N/m. The block slides an additional 21.0 cm before it is brought to rest momentarily by compressing the spring. (a) What is the value of d? (b) Where is the speed of the block at the maximum value?

To know more about spring visit

https://brainly.com/question/13998954

#SPJ4

[tex]p = \frac{w}{t} [/tex]

[tex]w = fdcosθ [/tex]

where p is power

w is work done

t is time in seconds

f is force

d is distance

f=600N

d=10

t=12

w=600 X 10

w=6000 Nm

p=6000/12

p=500 watts

Important Formulas:

[tex]w=Fd[/tex]

[tex]p=\dfrac{w}{t}[/tex]

work(measured in joules) = force(measured in newtons) * distance(measured in meters)

power(measured in watts) = work(measured in joules) / time(measured in seconds)

__________________________________________________________

Given:

[tex]F=600N[/tex]

[tex]d=10m[/tex]

[tex]t=12s[/tex]

[tex]p=?[/tex]

__________________________________________________________

Finding work:

[tex]w=Fd[/tex]

[tex]w=600\times10[/tex]

[tex]w=6000J[/tex]

__________________________________________________________

Finding power:

[tex]p=\dfrac{w}{t}[/tex]

[tex]p=\dfrac{6000}{12}[/tex]

__________________________________________________________

[tex]\fbox{p = 500 watts}[/tex]

A block of mass 0.40 kg and density 2900 kg/m3 is completely submerged under the water in static equilibrium on top of a spring (k = 50.0 N/m) that is fixed to the bottom of the container, the spring is compressed by 0.051 m.

To determine the amount that the spring is compressed, you will need to consider the mass of the block, the density of the block and the water, and the spring constant of the spring.

The weight of the block is equal to the mass of the block times the acceleration due to gravity.

The equation for the weight of the block can be written as:

W = m * g

where W is the weight of the block, m is the mass of the block (0.40 kg), and g is the acceleration due to gravity (9.8 m/s^2).

Plugging in the values, you get:

W = 0.40 kg * 9.8 m/s^2

W = 3.92 N

The buoyant force acting on the block is equal to the weight of the water displaced by the block. The weight of the water displaced by the block is equal to the volume of the block times the density of the water times the acceleration due to gravity.

The equation for the buoyant force can be written as:

F_b = V * rho_w * g

where F_b is the buoyant force, V is the volume of the block, rho_w is the density of the water (1000 kg/m^3), and g is the acceleration due to gravity (9.8 m/s^2).

The volume of the block can be calculated using the density of the block and the mass of the block.

The equation for the volume of the block can be written as:

V = m/rho

where V is the volume of the block, m is the mass of the block (0.40 kg), and rho is the density of the block (2900 kg/m^3).

Plugging in the values, you get:

V = 0.40 kg / 2900 kg/m^3

V = 0.0014 m^3

Plugging this value into the equation for the buoyant force, you get:

F_b = 0.0014 m^3 * 1000 kg/m^3 * 9.8 m/s^2

F_b = 1.37 N

The net force acting on the block is equal to the weight of the block minus the buoyant force.

The equation for the net force can be written as:

F_net = W - F_b

where F_net is the net force, W is the weight of the block, and F_b is the buoyant force.

Plugging in the values, you get:

F_net = 3.92 N - 1.37 N

F_net = 2.55 N

The spring force is equal to the spring constant times the amount that the spring is compressed.

The equation for the spring force can be written as:

F_s = k * x

where F_s is the spring force, k is the spring constant (50.0 N/m), and x is the amount that the spring is compressed.

Solving for x, you get:

x = F_s / k

Plugging in the values, you get:

x = 2.55 N / 50.0 N/m

x = 0.051 m

To know more about buoyancy

https://brainly.com/question/19168433

#SPJ4

Answer:

22,583.5 J

Explanation:

KE = 1/2mv²

KE = 1/2(47 kg)(31.0 m/s)² = 22,583.5 J

Answer:

Explanation:

Vertical acceleration.

Answer:

D

Explanation:

Direction of motion is positive right side

P = mv

P = m (final - initial)

P = 2 ( -1 - 3)

P = 8 Ns

(negative sign ignored)

I hope my answer helps you.

The impulse on the wall with a mass of the ball is 2 kg and the initial speed of wass 3 m/s and the final velocity is 1 m/s is 8 Ns. Hence, option D is correct.

Impulse equals the product of net force and changes in time. Impulse is also equal to the change in momentum. It is also defined as the force applied to an object with a short duration of time. The unit of impulse is Newton. seconds(Ns).

From the given,

mass of the ball (m) = 2kg

The initial speed of the ball (u) = 3m/s

the final speed of the ball (v) = -1 m/s.

Impulse (I) = Momentum (p)

Momentum (p) = mΔv

                         = m(v-u)

                         = 2(-1-3)

                         = 2(-4)

                         = -8.

Thus, the impulse on the wall is 8Ns.

Hence, the correct option is D.

To learn more about Impulse:

https://brainly.com/question/30466819

#SPJ2

The super keys of the relationship if a relation R(A, B, C, D) with four attributes A, B, C, and D is 8.

The quality of a feature is referred to as an attribute. The theory of attributes is concerned with the calculation of qualitative forms of qualities using quantitative measures. As a result, the characteristic requires slightly different types of statistical analyses than the variables do.

The given data,

Given three functional dependencies,

AB → C

BC → D

C → E

Finding the key of the relation, Compute closure of attribute,

{AB}⁺ = {A, B, C, D, E} {BC}⁺ = {B, C, D, E} {C}⁺ = {CE}

Only one candidate key is possible for a given relation = AB

Super keys of the relation = 2 (Total number of attributes in relations - Total number of attributes in each key).

Super keys of the relation = 2⁽⁵⁻²⁾

Super keys of the relation = 2³ = 8 keys

To know more about attributes:

https://brainly.com/question/30024138

#SPJ4