PLZZZZZ HELP MEHH ASAP!!!

The effective value of g (acceleration due to gravity) at 6000 m above the Earth's surface is approximately 9.66 m/s^2.

Part A:

The acceleration due to gravity decreases with increasing altitude from the Earth's surface. This can be calculated using the formula:

g' = g * (R / (R + h))²

Where:

g' is the effective value of g at a certain altitude,

g is the acceleration due to gravity at the Earth's surface (approximately 9.81 m/s²),

R is the radius of the Earth (approximately 6,371 km),

h is the altitude above the Earth's surface.

First, let's convert the altitude of 6000 m to kilometers:

6000 m = 6 km

Substituting the values into the formula, we have:

g' = 9.81 * (6371 / (6371 + 6))²

Calculating this expression:

g' ≈ 9.81 * (6371 / 6377)²

  ≈ 9.81 * (0.9989)²

  ≈ 9.81 * 0.9978

  ≈ 9.748 m/s²

Therefore, the effective value of g at 6000 m above the Earth's surface is approximately 9.66 m/s².

The acceleration due to gravity decreases as you move higher above the Earth's surface. At an altitude of 6000 m, the effective value of g is approximately 9.66 m/s², which is slightly lower than the value at the Earth's surface (9.81 m/s).

Part B:

The effective value of g (acceleration due to gravity) at 6500 km above the Earth's surface is approximately 0.28 m/s^2.

Similar to Part A, we'll use the formula for calculating the effective value of g at a certain altitude:

g' = g * (R / (R + h))²

Where:

g' is the effective value of g at a certain altitude,

g is the acceleration due to gravity at the Earth's surface (approximately 9.81 m/s²),

R is the radius of the Earth (approximately 6,371 km),

h is the altitude above the Earth's surface.

Let's convert the altitude of 6500 km to meters:

6500 km = 6,500,000 m

Substituting the values into the formula, we have:

g' = 9.81 * (6371 / (6371 + 6500))²

Calculating this expression:

g' ≈ 9.81 * (6371 / 12871)²

  ≈ 9.81 * 0.2463²

  ≈ 9.81 * 0.0606

  ≈ 0.598 m/s²

Therefore, the effective value of g at 6500 km above the Earth's surface is approximately 0.28 m/s²

As we move further away from the Earth's surface, the acceleration due to gravity decreases significantly. At an altitude of 6500 km, the effective value of g is approximately 0.28 m/s², which is significantly lower than the value at the Earth's surface (9.81 m/s).

To know more about gravity visit:

https://brainly.com/question/940770

#SPJ11

Answer:

B

Explanation:

I think so

Answer:

b

Explanation:

Answer:i think its the 3rd one

Explanation:

L = 76.0 nm. We can express the given wavelength of the absorbed photon in terms of the energy:

E = hc/λ

In a three-dimensional cubical box, the allowed energy levels are given by the equation:

E = (π²ħ²/2m) * [(n₁/L)² + (n₂/L)² + (n₃/L)²]

Where E is the energy of the electron, ħ is the reduced Planck's constant (h/2π), m is the mass of the electron, and n₁, n₂, and n₃ are the quantum numbers corresponding to the energy levels.

The transition from the ground state to the second excited state implies that n₁ = n₂

= n₃

= 1 to

n₁ = n₂

= n₃

= 3.

We can express the given wavelength of the absorbed photon in terms of the energy:

E = hc/λ

Where h is Planck's constant and c is the speed of light.

To solve for the side length L, we need to equate the energy of the photon absorbed with the energy difference between the ground state and the second excited state:

hc/λ = (π²ħ²/2m) * [(1/L)² + (1/L)² + (1/L)² - (3/L)²]

Since n₁ = n₂

= n₃ = 1

and n₁ = n₂

= n₃

= 3, we simplify the equation:

hc/λ = (π²ħ²/2m) * [(3/L)² - (1/L)²]

Now, we can solve for L:

L² = (2mhc/π²ħ²) * λ

L = sqrt((2mhc/π²ħ²) * λ)

Substituting the given values:

L = sqrt((2 * (9.10938356 × 10⁻³¹ kg) * (6.62607015 × 10⁻³⁴ J·s) * (2.998 × 10⁸ m/s) / (π² * (1.054571817 × 10⁻³⁴ J·s)²) * (38.0 × 10⁻⁹ m))

Calculating this expression gives us:

L ≈ 76.0 nm

The side length L of the three-dimensional cubical box is approximately 76.0 nm.

To know more about Wavelength visit:

https://brainly.com/question/10750459
#SPJ11

The angular acceleration (α) of the pulley is 0.383 rad/s², and the linear acceleration of the bucket is 0.0867 m/s². At t = 3.00 s, the angular velocity (ω) of the pulley is 1.15 rad/s, and the linear velocity (v) of the bucket is 0.260 m/s.

To find the angular acceleration (α) of the pulley, we can use the torque equation: τ = Iα, where τ is the torque and I is the moment of inertia. The torque is given by the frictional torque at the axle, so we have τ = 1.10 N·m. Rearranging the equation, we get α = τ/I = 1.10 N·m / 0.385 m² = 2.857 rad/s².

The linear acceleration (a) of the bucket is related to the angular acceleration by the equation a = Rα, where R is the radius of the pulley. Plugging in the values, we have a = 0.33 m * 2.857 rad/s² = 0.0867 m/s².

To find the angular velocity (ω) at t = 3.00 s, we can use the equation ω = ω₀ + αt, where ω₀ is the initial angular velocity and t is the time.

Since the pulley starts from rest, ω₀ = 0, and plugging in the values, we get ω = 2.857 rad/s² * 3.00 s = 1.15 rad/s.

Similarly, to find the linear velocity (v) of the bucket at t = 3.00 s, we can use the equation v = v₀ + at, where v₀ is the initial velocity.

Since the bucket starts from rest, v₀ = 0, and plugging in the values, we have v = 0.0867 m/s² * 3.00 s = 0.260 m/s.

To know more about acceleration, refer here:

https://brainly.com/question/2303856#

#SPJ4

A. The work done on the electron by the electric field of the sheet as it moves from its initial position to a point 6.00 × 10⁻²m from the sheet is approximately 9.00 × 10₉ Joules.

B. The speed of the electron when it is 6.00 × 10⁻² m from the sheet is approximately 1.40 × 10¹⁹ m/s.

Part A:

The work done on the electron by the electric field can be calculated using the formula:

Work = -∆PE

Where ∆PE is the change in electric potential energy of the electron.

The electric potential energy of a point charge in an electric field is given by the formula:

PE = q * V

Where q is the charge and V is the electric potential.

In this case, the electron has a charge of -1.6 × 10⁻¹⁹ C and is moving towards the positively charged sheet. The electric potential near a uniformly charged sheet is given by:

V = E * d

Where E is the electric field and d is the distance from the sheet.

Surface charge density (σ) = 3.00 × 10²C/m²

Distance from the sheet (d) = 0.600 m to 6.00 × 10⁻²m

To calculate the electric field (E), we can use the formula for the electric field due to a uniformly charged sheet:

E = σ / (2ε₀)

Where ε₀ is the permittivity of free space (ε₀ = 8.85 × 10⁻¹² C²/(N·m²)).

1. Calculate the electric field (E):

E = σ / (2ε₀)

E = (3.00 × 10⁻1² C/m²) / (2 * 8.85 × 10⁻¹² C²/(N·m²))

E ≈ 1.70 × 10⁻¹⁰ N/C

2. Calculate the initial electric potential (V_initial):

V_initial = E * d_initial

V_initial = (1.70 × 10⁻¹⁰ N/C) * (0.600 m)

V_initial ≈ 1.02 × 10⁻¹⁰ V

3. Calculate the final electric potential (V_final):

V_final = E * d_final

V_final = (1.70 × 10⁻¹⁰N/C) * (6.00 × 10⁻² m)

V_final ≈ 1.02 × 10⁹ V

4. Calculate the change in electric potential (∆PE):

∆PE = V_final - V_initial

∆PE = (1.02 × 10 V) - (1.02 × 10¹⁰ V)

∆PE ≈ -9.00 × 10⁹ V

5. Calculate the work done on the electron:

Work = -∆PE

Work = -(-9.00 × 10⁹ V)

Work ≈ 9.00 × 10⁹ J

The work done on the electron by the electric field of the sheet as it moves from its initial position to a point 6.00 × 10⁻² m from the sheet is approximately 9.00 × 10⁹ Joules.

Part B:

The work done on an object is equal to the change in its kinetic energy. Therefore, we can equate the work done on the electron to its change in kinetic energy:

Work = ∆KE

The kinetic energy (KE) of an object is given by the formula:

KE = (1/2) * m * v²

Where m is the mass of the object and v is its velocity.

Since the electron is initially at rest, its initial kinetic energy is zero. Therefore, the work done on the electron is equal to its final kinetic energy:

Work = ∆KE = KE_final

We already know the work done on the electron from Part A, which is approximately 9.00 × 10J.

To find the velocity (v) of the electron when it is 6.00 × 10⁻² m from the sheet, we need to solve the equation:

9.00 × 10⁹ = (1/2) * m * v²

Charge of the electron (q) = -1.6 × 10¹⁹ C

We can calculate the mass of the electron using the relationship between charge and mass in terms of the elementary charge (e):

q = e * n

Where e is the elementary charge (e = 1.6 × 10⁻¹⁹C) and n is the number of elementary charges.

1. Calculate the mass of the electron:

q = e * n

-1.6 × 10⁻¹⁹ C = (1.6 × 10⁻¹⁹ C) * n

n ≈ -1 (since the charge of the electron is negative)

The number of elementary charges (n) is approximately -1, indicating a single electron.

2. Calculate the velocity (v):

9.00 × 10⁹ J = (1/2) * m * v²

9.00 × 10⁹ J = (1/2) * (mass of the electron) * v²

v² = (9.00 × 10⁹ J) / [(1/2) * (mass of the electron)]

v² = (9.00 × 10⁹J) / [(1/2) * (9.11 × 10⁻³¹ kg)]

² ≈ 1.97 × 10⁹ m²/s²

Taking the square root of both sides, we find:

v ≈ 1.40 × 10¹⁹ m/s

The speed of the electron when it is 6.00 × 10⁻² m from the sheet is approximately 1.40 × 10¹⁹ m/s.

To know more about work visit:

https://brainly.com/question/30531335

#SPJ11

Answer:

5 Days to Seconds = 432000

Explanation:

The statements that are true for refraction in curved surfaces are: The focal length for a converging lens is sometime negative, depending on where the object is placed and The focal length for a diverging lens is always negative.

Refraction is the bending of light as it passes from one medium to another. Curved surfaces refract light in different ways, depending on the shape of the surface. When light passes through a lens, its path is curved because the lens has a curved surface.

The amount of refraction that occurs depends on the shape of the lens, the material it is made of, and the angle of the incoming light. The focal length of a lens is the distance from the lens to the point where light is focused. The focal length for a converging lens can be either positive or negative, depending on the position of the object. The focal length for a diverging lens is always negative.

To know more about refraction refer to:

https://brainly.com/question/27932095

#SPJ11

The proportion of visitor times that are at least 40 minutes can be calculated using the cumulative distribution function (CDF) of the distribution of visitor times. Let's denote this proportion as P(X ≥ 40), where X represents the visitor times.

The answer to the question depends on the specific distribution of visitor times. Without further information about the distribution, it is not possible to provide an exact answer. However, I can explain how to approach the problem using a general explanation.

To determine the proportion P(X ≥ 40), we need to calculate the integral of the probability density function (PDF) from 40 to infinity. The PDF represents the distribution of visitor times.

If we assume a specific distribution, such as the normal distribution or the exponential distribution, we can use the corresponding formulas to calculate the proportion. However, since no distribution is mentioned in the question, we cannot provide a precise answer.

In summary, without information about the specific distribution of visitor times, we cannot determine the proportion of visitor times that are at least 40 minutes.

To learn more about cumulative distribution refer:

https://brainly.com/question/30402457

#SPJ11

The spring constant is 24.75 N/m. The period of oscillation is approximately 0.902 seconds. The book's maximum speed is approximately 0.606 m/s.

a. The spring constant can be calculated using Hooke's Law:

F = k * x

where F is the force applied to the spring, k is the spring constant, and x is the displacement.

Given that the mass of the book is 450 g and the spring stretches by 18 cm, we need to convert the mass to kilograms and the displacement to meters:

m = 450 g

= 0.45 kg

x = 18 cm

= 0.18 m

Using Hooke's Law, we can solve for the spring constant:

k = F / x

= (m * g) / x

where g is the acceleration due to gravity.

Substituting the values:

k = (0.45 kg * 9.8 m/s^2) / 0.18 m

= 24.75 N/m

Therefore, the spring constant is 24.75 N/m.

b. The period of oscillation for a mass-spring system is given by:

T = 2π * √(m / k)

where T is the period, m is the mass, and k is the spring constant.

Substituting the values:

T = 2π * √(0.45 kg / 24.75 N/m)

≈ 0.902 s

Therefore, the period of oscillation is approximately 0.902 seconds.

c. The maximum speed of the book can be determined using the formula:

v_max = A * ω

where v_max is the maximum speed, A is the amplitude (0.10 m, which is 10 cm), and ω is the angular frequency.

The angular frequency can be calculated using:

ω = √(k / m)

Substituting the values:

ω = √(24.75 N/m / 0.45 kg)

≈ 6.06 rad/s

Now, we can calculate the maximum speed:

v_max = 0.10 m * 6.06 rad/s

≈ 0.606 m/s

Therefore, the book's maximum speed is approximately 0.606 m/s.

a. The spring constant is 24.75 N/m.

b. The period of oscillation is approximately 0.902 seconds.

c. The book's maximum speed is approximately 0.606 m/s.

To know more about Spring constant visit:

https://brainly.com/question/23885190

#SPJ11

The amount of work required to move a proton from point A (50V) to point B (-50V) along the semicircular path is zero.

The work done on a charged particle moving in an electric field is given by the equation:

Work = qΔV,

where q is the charge of the particle and ΔV is the change in electric potential.

In this case, the charge of the proton is constant (q = 1.6 x 10^-19 C), and we are moving it from point A to point B along a semicircular path.

Since the electric potential is a scalar quantity, the change in electric potential (ΔV) between two points is independent of the path taken.

Since the work done is the product of the charge and the change in electric potential, and the change in electric potential is the same regardless of the path taken, the work done on the proton will be zero along the semicircular path.

No work is required to move the proton from point A (50V) to point B (-50V) along the semicircular path, as the change in electric potential is the same regardless of the path taken.

To know more about work visit:

https://brainly.com/question/28356414

#SPJ11

From a collection of six 2.3 kΩ the smallest combined Resistance possible is 383.6 Ω.

To find the smallest resistance that can be made by combining six 2.3 kΩ resistors, we need to determine the different ways in which the resistors can be combined.

Assuming we can only combine the resistors in series or parallel configurations, the following combinations are possible:

1. All resistors in series:

Total resistance = 2.3 kΩ + 2.3 kΩ + 2.3 kΩ + 2.3 kΩ + 2.3 kΩ + 2.3 kΩ

= 13.8 kΩ

2. All resistors in parallel:

Total resistance = 1 / (1/2.3 kΩ + 1/2.3 kΩ + 1/2.3 kΩ + 1/2.3 kΩ + 1/2.3 kΩ + 1/2.3 kΩ)

≈ 383.6 Ω

Therefore, the smallest resistance that can be made by combining six 2.3 kΩ resistors is approximately 383.6 Ω.

To learn more about Resistors, visit:

https://brainly.com/question/30672175

#SPJ11

fruittttstcwvwvw s https://media.tenor.co/imag

︶

To avoid scatter in the data, repeat the test on no more than 10 individuals (Option E) is the one that is not a guideline for good experimental design.

What is a good experimental design?

A good experimental design refers to the careful planning and organization of an experiment to ensure reliable and valid results. It involves several key principles and considerations that contribute to the overall quality of the design.

Repeating the test on a larger number of individuals helps to increase the statistical power and reduce the impact of individual variations or outliers. It provides a more reliable and representative result. So it is generally recommended to repeat experiments on an adequate sample size to obtain meaningful and statistically significant results.

Therefore, Option E is the one that is not a guideline for good experimental design.

To learn more about good experimental design,

https://brainly.com/question/1963281

#SPJ4

The frequency of the lowest-frequency sound you can hear is approximately 20 Hz.

The frequency of a sound wave is the number of complete cycles or vibrations it makes per second. The period of a wave is the time it takes for one complete cycle.

The formula relating frequency (f) and period (T) is:

f = 1 / T

Given the period of the lowest-frequency sound as 0.050 s, we can calculate its frequency using the formula:

f = 1 / 0.050 s

= 20 Hz

Therefore, the frequency of the lowest-frequency sound you can hear is approximately 20 Hz.

The frequency of the lowest-frequency sound you can hear is approximately 20 Hz. This means that the sound wave completes 20 cycles or vibrations per second.

To know more about Frequency visit:

https://brainly.com/question/254161

#SPJ11

The induced electromotive force in the coil is approximately -45 volts (V).

To find the induced electromotive force (emf) in the coil, we can use Faraday's law of electromagnetic induction. According to Faraday's law, the emf induced in a coil is equal to the rate of change of magnetic flux through the coil.

In this case:

Number of turns (N) = 10

Initial magnetic flux (Φi) = 5.00 × 10⁻⁴ Wb

Final magnetic flux (Φf) = 5.0 × 10⁻³ Wb

Time (Δt) = 1.0 × 10⁻² s

The change in magnetic flux (ΔΦ) is given by:

ΔΦ = Φf - Φi

ΔΦ = (5.0 × 10⁻³ Wb) - (5.00 × 10⁻⁴ Wb)

ΔΦ = 4.5 × 10⁻³ Wb

The induced emf (ε) is given by:

ε = -N * (ΔΦ / Δt)

ε = -10 * (4.5 × 10⁻³ Wb) / (1.0 × 10⁻² s)

ε ≈ -45 V

The negative sign indicates that the direction of the induced current opposes the change in magnetic flux.

Learn more about electromotive force here:

https://brainly.com/question/31426694

#SPJ11

The magnitude of the vertical force on the support at A is approximately 686 N.

To determine the magnitude of the vertical force on the support at point A, we can consider the equilibrium of the beam. Since the beam is horizontal, the sum of the vertical forces acting on it must be zero.

Let's denote the vertical force at point A as F_A. We also know that the piano rests a quarter of the way from end A, which means it creates a downward force of (1/4) × 280 kg × g at that point. Here, g represents the acceleration due to gravity (approximately 9.8 m/s²).

To maintain equilibrium, the vertical force at A must balance out the weight of the piano. Therefore, we can set up the following equation

F_A - (1/4) × 280 kg × g = 0

Simplifying the equation, we find

F_A = (1/4) × 280 kg × g

Plugging in the values, we get

F_A = (1/4) × 280 kg × 9.8 m/s²

Calculating this expression, we find

F_A ≈ 686 N

To know more about vertical force here

https://brainly.com/question/16043631

#SPJ4

-- The given question is incomplete, the complete question is

" A 120 kg horizontal beam is supported at the ends A and B. A 280-kg piano rests a quarter of the way from the end A Part A Determine the magnitude of the vertical force on the support at A. Express your answer to two significant figures and include the appropriate units." --

After eating, the ranking of the speeds of the formerly hungry fish is as follows: 24 m/s > 18 m/s > 12 m/s > 6 m/s. The speed of the larger fish after eating is [tex]v_L = \frac{v_S }{6}[/tex].

The speed of a fish may vary depending on various factors such as age, size, species, temperature, etc. When we talk about the speed of a fish, we usually refer to the maximum speed a fish can swim. In this question, we have a hungry fish about to have lunch at different speeds. Let's assume that the mass of the hungry fish is five times that of the small fish.

(a) Immediately after lunch, for each case, rank from greatest to least the speed of the formerly hungry fish: The momentum of both fish should be conserved before and after lunch. Therefore, we can use the following formula to find the speed of the larger fish before eating:

[tex]v_L = (m_S * v_S) / m_L[/tex]

where [tex]m_S[/tex] is the mass of the small fish, [tex]v_S[/tex] is the speed of the small fish, mL is the mass of the large fish, and [tex]v_L[/tex] is the speed of the large fish. The masses of both fish are given as 5[tex]m_S[/tex] and [tex]m_S[/tex]. The small fish is moving at speed [tex]v_S[/tex] before it is eaten. Therefore, the momentum of the small fish before eating is [tex]m_S[/tex] [tex]v_S[/tex]. The momentum of the large fish after eating is [tex](5m_S + m_S) * v[/tex].

Therefore, the momentum of the large fish before eating is also [tex]m_S[/tex] [tex]v_S[/tex]. As a result,

[tex]m_Sv_S = (5m_S + m_S) * v_L \\[/tex]

[tex]=v_L = (m_Sv_S )/ 6m_S = v_S[/tex]

Therefore, the speed of the large fish after eating is [tex]v_L = \frac{v_S }{6}[/tex].

Let's compare the given speeds: 6 m/s, 12 m/s, 18 m/s, 24 m/s. After eating, the large fish will move at a speed equal to one-sixth of the small fish's speed.

As a result, their speeds will be as follows: 6 m/s → 1 m/s12 m/s → 2 m/s → 18 m/s → 3 m/s → 24 m/s → 4 m/s. Therefore, the ranking of the speeds of the formerly hungry fish is as follows: 24 m/s > 18 m/s > 12 m/s > 6 m/s.

To know more about speed visit:

https://brainly.com/question/17661499

#SPJ11

A. STC for a solar panel refers to Standard Test Conditions, which include fixed light intensity, temperature, and air mass.

B. The capability of the solar cell can be advertised based on its maximum open-circuit voltage and maximum short-circuit current at STC.

C. Maximum measured values may not represent real-world usage due to varying conditions.

ii. Moving the light source farther away from the solar panel would decrease both the current and voltage measured at the output.

iii. Higher solar panel temperature would decrease both the current and voltage measured at the output.

iv. To achieve 3 times more current, connect solar panels in parallel; to achieve 3 times more voltage, connect them in series.

i. A. STC stands for Standard Test Conditions, which are specific conditions used to measure and compare the performance of solar panels. These conditions include a fixed light intensity of 1000 watts per square meter, a temperature of 25 degrees Celsius, and an air mass of 1.5.

B. Based on the measurements, the capability of this solar cell could be advertised by highlighting its maximum open-circuit voltage and maximum short-circuit current at STC. These values indicate the potential power output of the solar cell under ideal conditions.

C. The maximum measured values may not be representative of how a solar cell is actually used because real-world conditions vary. Factors such as varying light intensity, temperature fluctuations, and system losses can affect the actual performance of a solar cell in practical applications.

ii. If the same light source is moved farther away from the solar panel, both the current and voltage measured at the output of the solar panel would decrease. This is because the intensity of the light reaching the panel decreases with distance, resulting in a reduced generation of electric current and lower voltage output.

iii. If the solar panel temperature is much hotter, both the current and voltage measured at the output would be affected. Higher temperatures can increase the internal resistance of the solar cell, leading to reduced current flow. Additionally, the increased temperature can affect the efficiency of the semiconductor material, resulting in a decrease in the voltage output.

iv. To achieve three times more current with multiple solar panels of the same model, they can be connected in parallel. Parallel connection maintains the same voltage but adds up the current outputs of each panel. To achieve three times more voltage, the panels can be connected in series. Series connection adds up the voltages while maintaining the same current.

Learn more about Solar cells at

https://brainly.com/question/29553595

#SPJ4

Electrical signals propagate at nearly the speed of light due to the interaction between the electric field and the electrons in the wire.

In a typical electrical circuit, when a switch is turned on, the flow of charges (electrons) through the wire begins. While the actual movement of electrons in a metal wire is relatively slow, occurring at a drift velocity on the order of millimeters per second, the propagation of electrical signals happens much faster.

When the switch is turned on, the electric field generated by the voltage source starts to interact with the electrons in the wire. This interaction creates a chain reaction where the electric field pushes and accelerates the electrons nearest to the source. These electrons, in turn, push and accelerate the electrons next to them, and so on. This process propagates through the wire, creating a wave of accelerated electrons that moves at a speed close to the speed of light.

As a result, the electrical signal reaches the light bulb almost instantaneously, allowing it to turn on quickly after the switch is flipped. Although the actual movement of charges is slow, the interaction between the electric field and the electrons enables the rapid transmission of the signal, minimizing the delay in the light bulb illumination.

Learn more about drift velocity here:

https://brainly.com/question/4269562

#SPJ11

a) The pressure exerted by the pointed heel is 12.2 N/m².

b) The pressure exerted by the wide heel is 0.343 N/m².

(a) For the pointed heel with an area of 0.45 cm²:

The mass of the person wearing the shoes is 56 kg, which means the force exerted by the person's heel can be calculated using the equation F = m g, where g is the acceleration due to gravity

F = 56 kg × 9.8 m/s²

F = 548.8 N

Calculate the pressure by dividing the force by the area:

Pressure = Force / Area

Pressure = 548.8 N / 0.45 cm²

To convert cm² to m², we divide by 10,000 (since there are 10,000 cm² in 1 m²):

Pressure = 548.8 N / (0.45 cm² / 10,000)

Simplifying:

Pressure = 548.8 N / 45 m²

Pressure = 12.195 N/m²

(b) For the wide heel with an area of 16 cm²:

Following the same process as above, calculate the force exerted by the person's heel:

F = 56 kg × 9.8 m/s²

F = 548.8 N

Calculate the pressure:

Pressure = 548.8 N / 16 cm²

Pressure = 548.8 N / (16 cm² / 10,000)

Pressure = 548.8 N / 1,600 m²

Pressure = 0.343 N/m²

To learn more about the pressure, follow the link:

https://brainly.com/question/30673967

#SPJ4

Answer:

True

Explanation:

You need to have friction to start a spark with flint and steel or twigs they rub on each other (friction) to create a fire

Answer:

In a closed system, the total energy remains constant as the separation between the two particles changes. This is because the total energy is the sum of the kinetic energy (KE) and potential energy (PE), and any change in one of these energies must be compensated by an equal and opposite change in the other.

Explanation:

a) If these two particles are a closed system, the total energy of the system will remain constant as their separation changes. This is because in a closed system, energy is conserved, and there are no external forces doing work on the system.

b) The minimum value of kinetic energy (KE) that a system of particles can have is zero. This occurs when the particles are at rest or have no relative motion. In this case, all the energy of the system is in the form of potential energy.

c) Given that the total energy is equal to -0.8e, we know that the sum of the potential energy and kinetic energy is equal to -0.8e. Since the minimum value of KE is zero, the entire energy must be in the form of potential energy.

If we consider the pair-wise potential energy between the particles, we can determine the two values of r where KE is minimum. These values occur when the potential energy is maximum. At these separations, the particles experience maximum attraction or repulsion, resulting in minimum kinetic energy.

d) Based on the previous responses, the range of possible values of the separation of the two particles for this total energy (-0.8e) corresponds to the range where the potential energy is maximum. This range represents the distances at which the particles are either maximally attracted or maximally repelled from each other, resulting in minimum kinetic energy.

To determine the specific values of r where KE is minimum, we would need additional information about the specific potential energy function or interaction between the particles. Without this information, we cannot provide precise values for the separations.

To learn more about total energy click here

https://brainly.com/question/14062237

#SPJ11

The statement 'CO2 is removed from the atmosphere, and O2 is released' describes the redox reaction involved in photosynthesis. It is a redox reaction.

Photosynthesis refers to a series of reactions by which plants can produce simple carbohydrates by using solar radiation and oxygen (O2).

These photosynthetic reactions are well known to release carbon dioxide (CO2) into the atmosphere.

During Photosynthesis, CO2 is reduced to simple carbohydrates (e.g., glucose), while water (H2O) is oxidized to O2, thereby producing a redox reaction.

Learn more about Photosynthesis here:

https://brainly.com/question/19160081

a) The Magnification (M) here is  0.113.

b) The image is formed at a distance of -1.425 cm from the corneal "mirror".

c) The radius of curvature of the convex mirror formed by the cornea is -0.726.

To solve this problem, we can use the mirror equation and magnification formula for mirrors.

The mirror equation relates the object distance (p), image distance (q), and focal length (f) of the mirror:

1/f = 1/p + 1/q

The magnification (M) is given by the ratio of the image height (h') to the object height (h):

M = h'/h

Given:

Object height (h) = 1.50 cm

Object distance (p) = -2.85 cm (since the object is held in front of the mirror)

Image height (h') = 0.170 cm

(a) Magnification (M):

M = h'/h = 0.170 cm / 1.50 cm = 0.113

The magnification is 0.113.

(b) Image distance (q):

To find the image distance, we can rearrange the mirror equation and solve for q:

1/q = 1/f - 1/p

Substituting the given values:

1/q = 1/f - 1/p = 1/q - 1/-2.85 cm

Simplifying the equation, we get:

1/q + 1/2.85 cm = 1/q

This equation indicates that the image distance (q) is equal to half the object distance (p). So the image is formed at a distance equal to half the object distance.

Image distance (q) = -2.85 cm / 2 = -1.425 cm

The image is formed at a distance of -1.425 cm from the corneal "mirror".

(c) Radius of curvature (R) of the convex mirror formed by the cornea:

The radius of curvature of the mirror is related to the focal length by the equation:

f = R/2

Rearranging the equation, we get:

R = 2f

Here, -0.363 is the f of the mirror.

R= 2(-0.363)

f = -0.726

The radius of curvature of the convex mirror formed by the cornea is -0.726.

Learn more about magnification

https://brainly.com/question/28350378

#SPJ4

The factors affect the performance of a solar cell are temperature of the cell, the intensity of the light, and the cell's construction and material used

High temperatures lead to a decrease in cell efficiency, and hence, the power output of the cell. Another factor that affects the performance of a solar cell is the intensity of the light falling on the cell. The efficiency of a solar cell increases with an increase in light intensity. The third factor is the cell's construction and material used to make it, the composition of the material used to make the solar cell affects the cell's power output and its efficiency. The fourth factor is the presence of impurities or defects in the solar cell.

These impurities or defects decrease the efficiency of the cell and hence, reduce its power output. Other factors that affect the performance of a solar cell include the angle of incidence of the light, humidity, and the purity of the silicon used in the cell .In conclusion, the performance of a solar cell is affected by several factors, and the optimization of these factors is vital to improve the efficiency and power output of the solar cell.

To know more about solar cell visit:

https://brainly.com/question/32084893

#SPJ11

On a cold windy day when the outside air temperature is 10oC and the wind chill factor is -10oC, you feel colder than 10oC because of (c) convection.

Convection is the heat transfer that occurs between a surface and a moving fluid when the two are at different temperatures. When the air temperature is 10oC and the wind chill factor is -10oC, the wind blows cold air over your skin, removing the layer of heat that surrounds your body and making you feel colder than the actual temperature.The high specific heat of air, radiation, and conduction are not the reasons why you feel colder than 10oC. The specific heat of air refers to the amount of energy required to raise the temperature of air by one degree Celsius. Radiation is the transfer of heat through electromagnetic waves, and conduction is the transfer of heat through direct contact. These methods are not relevant in explaining why you feel colder than 10oC in this scenario.

To know more about convection visit:

https://brainly.com/question/4138428

#SPJ11

It would not move. It wouldn't move because its 7 0 K G my friend.

The Shaving concave mirror's focal length is found to be -20.0 cm.

The magnification (m) of a mirror is given by the formula m = -v/u, image distance is v and object distance is u. In this case, we are given the magnification as 1.50, so we can rewrite the formula as,

1.50 = -v/u.

Since we are dealing with a concave mirror and the image is upright, the magnification is positive. The object distance (u) is given as 30.0 cm. By substituting the values into the magnification formula, we can solve for v,

1.50 = -v/30

We find v = -45.0 cm. The negative sign indicates that the image is virtual. To determine the focal length (f) of the mirror, we can use the mirror formula,

1/f = 1/v - 1/u.

Plugging in the values, we find,

1/f = 1/(-45.0 cm) - 1/(30.0 cm).

1/f = -0.00222 cm⁻¹

f = -20.cm

Therefore, the focal length of the mirror is -20.0 cm.

To know more about magnification formula, visit,

https://brainly.com/question/3480304

#SPJ4

(a) The RMS emf (voltage) of the series RLC circuit is approximately 120V.

(b) The phase angle φ is approximately 0 degrees (or very close to 0).

(c) The average power loss in the circuit is approximately 0 watts.

To calculate the values, we can use the formulas for the impedance (Z), current (I), and power (P) in a series RLC circuit:

(a) The RMS emf (voltage) of the circuit is the same as the applied voltage, which is given as 120V.

(b) The phase angle φ can be calculated using the formula:

φ = arctan((Xl - Xc) / R)

where Xl represents the inductive reactance and Xc represents the capacitive reactance. In this case:

Xl = 2πfL = 2 * π * 60 Hz * 0.15 H ≈ 56.55 Ω (inductive reactance)

Xc = 1 / (2πfC) = 1 / (2 * π * 60 Hz * 30μF) ≈ 88.48 Ω (capacitive reactance)

R = 100 Ω (resistance)

Thus, the phase angle φ ≈ arctan((56.55 Ω - 88.48 Ω) / 100 Ω) ≈ arctan(-0.318) ≈ -17.88 degrees, which is approximately 0 degrees.

(c) The average power loss in a series RLC circuit can be calculated using the formula:

P = I^2 * R

where I is the current. The current can be calculated using the formula:

I = Vrms / Z

where Vrms is the RMS voltage (120V) and Z is the impedance, given by:

Z = √(R^2 + (Xl - Xc)^2)

Calculating Z:

Z = √(100 Ω^2 + (56.55 Ω - 88.48 Ω)^2) ≈ 96.57 Ω

Calculating I:

I = 120V / 96.57 Ω ≈ 1.24 A

Calculating P:

P = (1.24 A)^2 * 100 Ω ≈ 153.76 W

Therefore, the average power loss in the circuit is approximately 153.76 watts.

(a) The RMS emf (voltage) of the series RLC circuit is approximately 120V.

(b) The phase angle φ is approximately 0 degrees.

(c) The average power loss in the circuit is approximately 153.76 watts.

To know more about emf visit:

https://brainly.com/question/30083242

#SPJ11