The ratio of the periods, t1/t2, for the two masses m1 and m2 in simple harmonic motion (SHM) on springs with the same spring constant k is 1:2.
In SHM, the period of oscillation (T) is given by the equation:
T = 2π√(m/k)
where T is the period, m is the mass, and k is the spring constant.
Let's calculate the periods for the two masses:
For mass m1:
T1 = 2π√(m1/k)
For mass m2 (which is 4 times m1):
T2 = 2π√(m2/k)
To find the ratio of the periods, we divide T1 by T2:
t1/t2 = (T1)/(T2)
Substituting the expressions for T1 and T2:
t1/t2 = (2π√(m1/k))/(2π√(m2/k))
Canceling out the common factors of 2π, we get:
t1/t2 = (√(m1/k))/(√(m2/k))
Since m2 = 4m1, we can substitute this value:
t1/t2 = (√(m1/k))/(√((4m1)/k))
Simplifying further:
t1/t2 = (√(m1/k))/(2√(m1/k))
The square root terms cancel out, resulting in:
t1/t2 = 1/2
The ratio of the periods, t1/t2, for the two masses m1 and m2 that oscillate in SHM on springs with the same spring constant k is 1:2.
This means that the period of oscillation for the larger mass (m2) is twice the period of the smaller mass (m1).
To know more about period visit:
https://brainly.com/question/29813582
#SPJ11
A heat engine supposedly receives 500 kJ/s of heat from an 1100-K source and rejects 300 kJ/s to a low temperature sink at 300-K. a. Is this possible or impossible? Explain. b. What would be the net rate of change of entropy for this system? c. What is the thermal efficiency of this heat engine? d. Ideally, what is the maximum efficiency that the heat engine can achieve if it receives heat from 1100-K source and rejects heat to a temperature sink at 300-K.
It is possible for a heat engine to receive 500 kJ/s of heat from an 1100-K source and reject 300 kJ/s to a low-temperature sink at 300 K. This scenario is in accordance with the second law of thermodynamics, which states that heat naturally flows from a higher temperature to a lower temperature.
The net rate of change of entropy for this system can be calculated using the equation ΔS = Q_in / T_in - Q_out / T_out, where ΔS is the change in entropy, Q_in is the heat received, Q_out is the heat rejected, T_in is the temperature of the heat source, and T_out is the temperature of the heat sink. The thermal efficiency of a heat engine is given by the formula η = (W_out / Q_in) * 100%, where η is the efficiency, W_out is the work output, and Q_in is the heat input. The maximum efficiency that a heat engine can achieve is given by the Carnot efficiency, which is determined solely by the temperatures of the heat source and heat sink.
To learn more about thermodynamics:
https://brainly.com/question/1368306
#SPJ11
) A cable car at a ski resort carries skiers a distance of 6. 8 km. The cable which moves the car is driven by a pulley with diameter 3. 0 m. Assuming no slippage, how fast must the pulley rotate for the cable car to make the trip in 12 minutes
The pulley must rotate at a speed of approximately 1.99 radians per second for the cable car to make the trip in 12 minutes.
To determine the rotational speed of the pulley, we need to calculate the angular velocity (ω) in radians per second.
Distance traveled by the cable car = 6.8 km
Time taken to make the trip = 12 minutes
First, let's convert the distance to meters:
Distance = 6.8 km = 6,800 meters
Next, let's convert the time to seconds:
Time = 12 minutes = 12 * 60 seconds = 720 seconds
The linear speed (v) of the cable car can be calculated using the formula:
v = distance / time
v = 6,800 meters / 720 seconds
v ≈ 9.44 m/s
The linear speed of the cable car is equal to the circumference of the pulley multiplied by its angular velocity:
v = 2πrω
where r is the radius of the pulley (half of its diameter).
Given the diameter of the pulley is 3.0 m, the radius is:
r = 3.0 m / 2 = 1.5 m
Substituting the values into the equation:
9.44 m/s = 2π(1.5 m)ω
To solve for ω, divide both sides by 2π(1.5 m):
ω = 9.44 m/s / (2π(1.5 m))
ω ≈ 1.99 rad/s
Therefore, the pulley must rotate at a speed of approximately 1.99 radians per second for the cable car to make the trip in 12 minutes.
For more such questions on speed , click on:
https://brainly.com/question/4931057
#SPJ8
At the beginning of a roller coaster ride, the roller coaster car has an initial energy
mostly in the form of PE. Which statement explains why the fastest speeds of the car
will be at the lowest points in the ride?
a. At the bottom of the slope kinetic energy is at its maximum value and potential
energy is at its minimum value.
b. At the bottom of the slope potential energy is at its maximum value and kinetic
energy is at its minimum value.
c. At the bottom of the slope both kinetic and potential energy reach their maximum
values
d. At the bottom of the slope both kinetic and potential energy reach their minimum
values.
Explanation:
The potential energy of the roller coaster is due to its position. It can be calculated as :
P = mgh
Where
m is mass, g is acceleration due to gravity and h is height.
The kinetic energy of an object is given by :
[tex]K=\dfrac{1}{2}mv^2[/tex]
Where
v is the speed of the object
At lowest point, the potential energy of the roller coaster is converted to the kinetic energy. So, At the bottom of the slope kinetic energy is at its maximum value and potential energy is at its minimum value. That's why the speed of the cars is at the lowest points in the ride.
We have that for the Question "Which statement explains why the fastest speeds of the car will be at the lowest points in the ride?"
Option A (At the bottom of the slope kinetic energy is at its maximum value and potential energy is at its minimum value) best explains itoption a explains why the fastest speeds of the car will be at the lowest points in the ride because potential energy decreases with decrease in height. Here the decreased potential energy is converted to the kinetic energy.
For more information on this visit
https://brainly.com/question/23379286
what is a waves frequency
Answer:
the number of times the crest of a wave hits a certain point
the more waves, the higher the frequency
Explanation:
a 17.0-n force stretches a wire 0.650 cm. (a) what force will stretch a similar piece of wire 1.87 cm? (b) a force of 21.3 n is applied to a similar piece of wire. how far will it stretch?
(a) To find the force that will stretch a similar piece of wire to 1.87 cm, we can use the concept of Hooke's Law. Hooke's Law states that the force required to stretch or compress a spring (or wire) is directly proportional to the displacement or change in length.
Given that the original force is 17.0 N and it stretches the wire by 0.650 cm, we can set up a proportion to find the force required for a 1.87 cm stretch.
Let F1 be the original force, x1 be the original displacement, F2 be the unknown force, and x2 be the desired displacement. The proportion can be expressed as:
F1 / x1 = F2 / x2
Substituting the given values, we have:
17.0 N / 0.650 cm = F2 / 1.87 cm
Now we can solve for F2:
F2 = (17.0 N / 0.650 cm) * 1.87 cm
F2 ≈ 48.8 N
Therefore, a force of approximately 48.8 N will stretch a similar piece of wire to 1.87 cm.
(b) To determine how far a similar piece of wire will stretch when a force of 21.3 N is applied, we can use Hooke's Law again.
Using the same variables as before, the proportion can be set up as:
F1 / x1 = F2 / x2
Substituting the given values:
17.0 N / 0.650 cm = 21.3 N / x2
Solving for x2:
x2 = (21.3 N / 17.0 N) * 0.650 cm
x2 ≈ 0.815 cm
Therefore, a force of 21.3 N will cause the wire to stretch approximately 0.815 cm.
To know more about force visit :
https://brainly.com/question/12785175
#SPJ11
Calculate the magnitude of the angular momentum of the earth in a circular orbit around the sun.
L=
Is it reasonable to model it as a particle? Yes or No?
Calculate the magnitude of the angular momentum of the earth due to its rotation around an axis through the north and south poles, modeling it as a uniform sphere.
uploaded image=
The magnitude of the angular momentum of the Earth in a circular orbit around the Sun can be calculated as 3.53 x 10²⁹ kg·m²/s. It is reasonable to model the Earth's motion around the Sun as a particle due to its relatively small size compared to the orbital radius.
The magnitude of the angular momentum of the Earth due to its rotation around an axis through the north and south poles, modeling it as a uniform sphere, is approximately 7.07 x 10³³ kg·m²/s.
The Earth's rotation involves the collective angular momentum of its constituent particles. Modeling it as a uniform sphere provides a simplified representation, assuming a constant mass distribution throughout.
Determine how to find the magnitude of the angular momentum of the earth in a circular orbit?For a particle in circular motion, the angular momentum can be calculated as the product of the mass, velocity, and radius of the orbit.
Using the mass of the Earth (5.97 x 10²⁴ kg), the average orbital velocity (2.98 x 10⁴ m/s), and the distance from the Earth to the Sun (1.50 x 10¹¹ m),
we can calculate the angular momentum as L = (5.97 x 10²⁴ kg) * (2.98 x 10⁴ m/s) * (1.50 x 10¹¹ m) = 3.53 x 10²⁹ kg·m²/s.
Determine find the magnitude of the angular momentum of the earth?For a rotating object, the angular momentum can be calculated as the product of the moment of inertia and the angular velocity.
Considering the Earth as a uniform sphere, the moment of inertia (I) can be approximated as (2/5) * M * R², where M is the mass of the Earth and R is its radius.
The angular velocity (ω) is determined by the Earth's rotational period (T), with ω = 2π/T.
Substituting the values of M (5.97 x 10²⁴ kg) and R (6.37 x 10⁶ m) and using the rotational period of the Earth (T = 24 hours or 8.64 x 10⁴ s),
we can calculate the angular momentum as L = [(2/5) * (5.97 x 10²⁴ kg) * (6.37 x 10⁶ m)²] * [2π/(8.64 x 10⁴ s)] = 7.07 x 10³³ kg·m²/s.
To know more about velocity, refer here:
https://brainly.com/question/30559316#
#SPJ4
Tell me what the laws of thermodynamics are in a simple way
Answer:
The first law, also known as Law of Conservation of Energy, states that energy cannot be created or destroyed in an isolated system. The second law of thermodynamics states that the entropy of any isolated system always increases. The third law of thermodynamics states that the entropy of a system approaches a constant value as the temperature approaches absolute zero.
Explanation:
a 52-kg person riding a bike puts all her weight on each pedal when climbing a hill. the pedals rotate in a circle of radius 17 cm . What is the maximum torque she exerts?
The maximum tοrque exerted by the persοn is 86.6 Nm.
What is a tοrque?Tοrque is a measure οf the tendency οf a fοrce tο rοtate an οbject arοund a specific axis. It is alsο referred tο as the mοment οf fοrce.
Given:
Mass οf the persοn (m) = 52 kg
Radius οf the circle fοrmed by the pedals (r) = 17 cm = 0.17 m
Weight οf the persοn (W) = m * g, where g is the acceleratiοn due tο gravity (apprοximately 9.8 m/s²)
Tο find the fοrce exerted by the persοn οn each pedal, we can use the equatiοn:
Fοrce (F) = Weight (W)
The weight οf the persοn is given by:
W = m * g
Substituting the given values:
W = 52 kg * 9.8 m/s²
W ≈ 509.6 N
Nοw, the maximum tοrque (τ) can be calculated using the equatiοn:
Tοrque (τ) = Fοrce (F) * Lever Arm (r)
τ = F * r
Substituting the values:
τ = 509.6 N * 0.17 m
τ ≈ 86.6 N·m
Therefοre, the maximum tοrque exerted by the persοn is apprοximately 86.6 N·m.
To learn more about torque,
https://brainly.com/question/28220969
#SPJ4
This object was moving at a velocity of 1.0 m/s east at the end of 4.0 seconds. Determine the average and instantaneous velocities in m/s at 6.0 seconds.
Average = 1.0 m/s east; instantaneous = 4.0 m/s east
Average = 4.0 m/s east; instantaneous = 6.0 m/s east
Average = 0.67 m/s east; instantaneous = 0 m/s
Average = 1.0 m/s east; instantaneous = 0 m/s
The average and instantaneous velocities in m/s at 8.0 seconds would be 0.5 m/s and 0 m/s respectively, therefore the correct answer is option D.
What is Velocity?
The total displacement covered by any object per unit of time is known as velocity. It depends on the magnitude as well as the direction of the moving object.
As given in the problem, this object was moving at a velocity of 1.0 m/s east at the end of 4.0 seconds.
The average velocity of the object = ( 4 - 0 ) / (8 -0)
The instantaneous velocity of the object = 0 m/s
Thus, the average and instantaneous velocities in m/s at 8.0 seconds would be 0.5 m/s and 0 m/s respectively, therefore the correct answer is option D.
Answer:
Explanation:
Answer:
Average = 0.67 m/s east; instantaneous = 0 m/s
Explanation:
took the test
The behavior of the light incident upon this page best illustrates the phenomenon of
A)
diffuse reflection
B)
regular reflection
C)
diffraction
D)
refraction
Answer:
diffraction
Explanation:
The behavior of the light incident upon this page best illustrates the phenomenon of diffraction
hope it help:)
The behaviour of such incident light on just this pages adequately exemplifies the phenomena called Diffraction. A further explanation is below.
DiffractionThe broadening out of waveforms when they transit through such an apertures anywhere around obstructions generally referred to as diffraction.
It happens whenever the aperture as well as obstruction seems of the equivalent order of magnitude as that of the transmitted beam's wavelength.
Thus the approach above i.e., option C is correct.
Find out more information about Diffraction here:
https://brainly.com/question/16749356
suppose you increase the amplitude of oscillation of a mass vibrating on a spring.
Consider increasing the mass vibrating on a spring's oscillation's amplitude. The claims (A) and (D) regarding this mass are true.
A. Its maximum speed increases.
D. Its maximum kinetic energy increases.
Here is the explanation :
When you increase the amplitude of oscillation of a mass vibrating on a spring, two correct statements about the mass are:
A. Its maximum speed increases: The maximum speed of the mass occurs at the amplitude of the oscillation. Increasing the amplitude means the mass travels a greater distance from the equilibrium position, leading to a higher maximum speed during its oscillation.
D. Its maximum kinetic energy increases: The kinetic energy of the mass is directly proportional to the square of its speed. As the maximum speed increases, the maximum kinetic energy also increases because kinetic energy is dependent on the square of the speed.
The other two statements are incorrect:
B. Its period of oscillation does not change: The period of oscillation is determined by the properties of the spring and the mass and is independent of the amplitude. Increasing the amplitude does not affect the period of oscillation.
C. Its maximum acceleration does not change: The maximum acceleration of the mass occurs at the extreme points of its motion, which are determined by the properties of the spring and the mass. Increasing the amplitude does not change the maximum acceleration.
To know more about the spring's oscillation's amplitude refer here :
https://brainly.com/question/29569975#
#SPJ11
Complete question :
Suppose you increase the amplitude of oscillation of a mass vibrating on a spring. Which of the following statements about this mass are correct? (There may be more than one correct choice.)
A. Its maximum speed increases.
B. Its period of oscillation increases.
C. Its maximum acceleration increases.
D. Its maximum kinetic energy increases.
calculate the average translational kinetic energy, k, for one mole of gas at 413 k. translational kinetic energy is sometimes called average kinetic energy.
K = (3/2) * 8.314 J/(mol·K) * 413 K. Calculating this expression will give us the average translational kinetic energy for one mole of gas at 413 K.
The average translational kinetic energy, K, for one mole of gas at a given temperature can be calculated using the equation:K = (3/2) * R * T
Where: K is the average translational kinetic energy
R is the ideal gas constant (8.314 J/(mol·K))
T is the temperature in Kelvin
Substituting the given values into the equation:
K = (3/2) * 8.314 J/(mol·K) * 413 K
Calculating this expression will give us the average translational kinetic energy for one mole of gas at 413 K.
To learn more about kinetic energy:
https://brainly.com/question/999862
#SPJ11
what is the magnifying power of an astronomical telescope using a reflecting mirror whose radius of curvature is 5.7 m and an eyepiece whose focal length is 2.9 cm ? follow the sign conventions.
We get: Magnifying Power = -(2.85 m / 0.029 m) ≈ -98.28. The magnifying power of an astronomical telescope can be calculated using the formula: Magnifying Power = -(fo/fe), where fo is the focal length of the objective (reflecting mirror) and fe is the focal length of the eyepiece.
Given that the radius of curvature of the reflecting mirror is 5.7 m, the focal length can be determined using the relation: Focal Length = Radius of Curvature / 2. So, the focal length of the objective is 5.7 m / 2 = 2.85 m.
Converting the focal length of the eyepiece to meters, we have 2.9 cm = 0.029 m.
Substituting the values into the magnifying power formula, we get: Magnifying Power = -(2.85 m / 0.029 m) ≈ -98.28
The negative sign indicates an inverted image, and the magnitude of the magnifying power suggests that the image appears 98.28 times larger than the object.
To know more about astronomical telescope, refer here:
https://brainly.com/question/31038565#
#SPJ11
a piece of 14-gauge copper wire (meaning that it has a diameter of 1.63mm) has a resistance of 0.128 . the resistivity of copper is . what must be the length of the wire?
The length of the copper wire must be approximately 44.2 meters for it to have a resistance of 0.128 ohms, assuming a 14-gauge wire with a diameter of 1.63 mm and using the resistivity of copper.
To find the length of the wire, we can use Ohm's Law, which states that the resistance (R) is equal to the product of the resistivity (ρ), the length (L), and the cross-sectional area (A) of the wire, divided by the diameter (d) of the wire squared.
The formula can be written as:
R = ρ * (L / A)
Resistance (R) = 0.128 ohms
Resistivity of copper (ρ) = (1.68 × 10^-8) ohm-meter (at 20°C)
Diameter (d) = 1.63 mm = 0.00163 meters (converted from millimeters to meters)
We need to find the length (L) of the wire.
To calculate the cross-sectional area (A) of the wire, we can use the formula for the area of a circle:
A = π * (d/2)^2
Plugging in the values, we have:
A = 3.14159 * (0.00163 / 2)^2
A ≈ 2.08 x 10^-6 square meters
Rearranging Ohm's Law to solve for the length (L), we get:
L = (R * A) / ρ
Substituting the given values:
L = (0.128 * 2.08 x 10^-6) / (1.68 x 10^-8)
L ≈ 44.2 meters
The length of the copper wire must be approximately 44.2 meters for it to have a resistance of 0.128 ohms, assuming a 14-gauge wire with a diameter of 1.63 mm and using the resistivity of copper.
To know more about resistivity visit:
https://brainly.com/question/13735984
#SPJ11
A wave has a wavelength of 2 meters and a frequency of 1.5 hz. What is its speed
Answer:
3m/s is the answer.
Explanation:
f = c/λ
f = frequency
c = speed (m/s)
λ = wavelength
f = c/λ
1.5 = c/2
c = 3m/s
You are looking for a mirror that will enable you to see a 3.6-times magnified virtual image of an object that is placed 4.9 cm the mirror's vertex. What kind of mirror will you need? What should the mirror's radius of curvature be, in centimeters? R=
To achieve a 3.6-times magnified virtual image, you will need a concave mirror with a radius of curvature (R) of approximately -1.067 cm.
To achieve a 3.6-times magnified virtual image, you will need a concave mirror. Concave mirrors have the ability to create magnified virtual images.
To determine the radius of curvature of the mirror (R), we can use the mirror formula
1/f = 1/v - 1/u
where f is the focal length of the mirror, v is the image distance (negative for virtual images), and u is the object distance.
Given that the magnification (m) is equal to -v/u, and the desired magnification is 3.6, we can write
m = -v/u
3.6 = -v/u
Since the image is virtual, the image distance (v) will be negative. Also, the object distance (u) is given as 4.9 cm.
Plugging in the values into the magnification equation, we get
3.6 = -v/4.9
Solving for v, we find
v = -4.9/3.6
v ≈ -1.3611 cm
Now, substituting the values of v and u into the mirror formula, we have
1/f = 1/(-1.3611) - 1/4.9
Simplifying the equation, we get
1/f ≈ -0.7335 - 0.2041
1/f ≈ -0.9376
Taking the reciprocal of both sides, we find
f ≈ -1.067 cm
The negative sign indicates that the mirror has a concave shape.
To know more about concave mirror here
https://brainly.com/question/31379461
#SPJ4
A rainbow is produced by a. Reflection of sunlight by clouds. b. Refraction of sunlight in the human eye. c. None of the above. d. Refraction, dispersion, and internal reflection in water droplets.
A rainbow is produced by the combined effects of refraction, dispersion, and internal reflection of sunlight within water droplets in the atmosphere. The correct option is D.
When sunlight passes through water droplets suspended in the air, the light is refracted, or bent, as it enters and exits the droplets. This refraction causes the different colors of light to separate due to their varying wavelengths, a phenomenon known as dispersion.
Additionally, once inside the droplets, the light undergoes multiple internal reflections before finally exiting. These reflections further separate the colors and contribute to the formation of the rainbow.
Therefore, option d, which includes refraction, dispersion, and internal reflection in water droplets, is the correct explanation for the production of a rainbow.
To know more about rainbow, refer here:
https://brainly.com/question/15172132#
#SPJ11
To what temperature would you have to heat a brass rod for it to be 2.5 % longer than it is at 30 ∘C?
Express your answer to two significant figures and include the appropriate units.
The temperature to which you would have to heat a brass rod for it to be 2.5% longer than it is at 30°C is 218°C (two significant figures).
Explanation: Let's begin with the formula for linear thermal expansion.
ΔL = αLΔT
Here, ΔL is the change in length,α is the coefficient of linear expansion, L is the original length, andΔT is the change in temperature.
The equation can be rearranged as follows:
α = ΔL/LΔT
The coefficient of linear expansion is the change in length per degree Celsius per unit length.
The value of α for brass is given as 1.9 × 10^-5/°C.
So, to solve for the change in temperature required to achieve a 2.5% increase in length,
substitute the values into the formula above:
α = ΔL/L
ΔT1.9 × 10^-5/°C
α= (2.5/100)L/ΔT
The L value can be taken as 1 cm for this problem,
giving:
1.9 × 10^-5/°C = (2.5/100)(1 cm)/ΔT
ΔT = 1 cm/(2.5/100)(1.9 × 10^-5/°C)
ΔT = 218°C (two significant figures).
to know more about thermal expansion visit:
https://brainly.com/question/31608640
#SPJ11
A material kept at high temperature is seen to emit photons with energies of 0.3 eV, 0.5eV, 0.8 eV, 2.0 eV, 2.5 eV, and 2.8 eV. These are the only photon energies observed. It is now cooled down to a very low temperature so that it is not emitting photons anymore. If a beam of light with a continuous range of energies from 0.01 eV to 10 eV shines on the material, what photon energies in this beam will correspond to dark absorption lines?
1. 0.3 eV, 0.5 eV, 2.8 eV
2. 0.3 eV, 0.5 eV, 0.8 eV
3. 0.3 eV, 0.8 eV, 2.8 eV
4. 0.8 eV, 2.0 eV, 2.8 eV
5. 0.5 eV, 0.8 eV, 2.8 eV
6. 0.3 eV, 2.5 eV, 2.8 eV
Answer:
the correct one is 2
Explanation:
The emission and arcion spectra are similar, in the emission spectra a heated material emits photons for the internal transitions of the electrons, in the absorption spectrum the continuous emission of a lamp is absorbed at the energies that the material has transitions.
In our case the material is low early, so all the electrons are in their base states.
As the light beam has all wavelengths, those corresponding to the first emission of the material will be observed.
When reviewing the answers, the correct one is 2
1) How do the required CL and AOA for your specific aircraft (at a specific weight) change with changes in airspeed? (provide specific examples)
2) What happens if the required CL is larger than CLmax of your airfoil, and what speed regime is usually associated with that condition?
The aircraft is a Cessna 152 please let me know if you need anymore info.
The Cessna 152 is a popular general aviation aircraft. To understand how the required coefficient of lift (CL) and angle of attack (AOA) change with airspeed.
We need to consider the aerodynamic characteristics of the aircraft.
1. Relationship between CL, AOA, and Airspeed:
As airspeed changes, the required CL and AOA for maintaining level flight at a specific weight in the Cessna 152 will also change. Generally, as airspeed increases, the required CL decreases, which means the AOA will also decrease.
At lower airspeeds, such as during takeoff or landing, the Cessna 152 typically operates at higher CL and AOA values. This is because the aircraft needs more lift to overcome its weight and maintain level flight or climb. For example, during takeoff, the required CL and AOA will be relatively high to generate sufficient lift at low speeds.
As the aircraft accelerates and reaches its cruise speed, the required CL and AOA will decrease. This is because the increased airspeed provides more lift and reduces the need for a high CL. In cruise, the Cessna 152 typically operates at lower CL and AOA values compared to takeoff and landing.
To provide specific examples, let's consider the Cessna 152 at a specific weight:
Takeoff: At a lower airspeed during takeoff, the required CL could be around 1.3 to 1.5, and the AOA might be around 10 to 12 degrees.
Cruise: Once the aircraft reaches its cruise speed, the required CL decreases. It could be around 0.6 to 0.8, and the AOA might reduce to around 2 to 4 degrees.
These values are approximate and may vary depending on factors such as weight, aircraft configuration, and atmospheric conditions. It's important to consult the specific aircraft's performance charts or pilot operating handbook for precise values.
CLmax Limit and Associated Speed Regime:
If the required CL exceeds the maximum lift coefficient (CLmax) of the Cessna 152's airfoil, the aircraft will no longer be able to generate sufficient lift at that particular AOA. This condition is commonly associated with the aircraft reaching its critical angle of attack (AOA), beyond which it experiences an aerodynamic stall.
In the Cessna 152, the airfoil typically exhibits a CLmax around 1.4 to 1.6. If the required CL exceeds this value, the aircraft will not be able to maintain level flight or continue to generate enough lift. This condition is often encountered during high-AOA maneuvers, such as during a go-around or during certain phases of stall recovery.
It is important for pilots to be aware of the aircraft's limitations and the associated speed regime where exceeding CLmax may occur. Proper training and understanding of the aircraft's performance characteristics are crucial to ensure safe operation.
To learn more about angle of attack (AOA) visit:
brainly.com/question/31391279
#SPJ11
PLEASE HELP ME I AM TIMED!
Answer: C
Explanation:
A cyclist starts from rest and pedals such that the wheels of his bike have a constant angular acceleration. After 18.0 s, the wheels have made 89 rev.
a.) What is the angular acceleration of the wheels?
b.) What is the angular velocity of the wheels after 18.0 s?
c.) If the radius of the wheel is 36.0 cm, and the wheel rolls without slipping, how far has the cyclist traveled in 18.0 s?
a) The angular acceleration of the wheels is approximately 0.861 rad/s². b) The angular velocity of the wheels after 18.0 s is approximately 15.5 rad/s. c) The cyclist has traveled approximately 201.06 meters in 18.0 seconds.
Time (t) = 18.0 s
Number of revolutions (N) = 89
Radius of the wheel (r) = 36.0 cm = 0.36 m
a) The angular acceleration (α) can be calculated using the formula
α = (2πN) / t²
where N is the number of revolutions and t is the time.
α = (2πN) / t²
α = (2π × 89) / (18.0²)
α ≈ 0.861 rad/s²
b) The angular velocity (ω) can be calculated using the formula
ω = αt
ω = αt
ω = 0.861 * 18.0
ω ≈ 15.5 rad/s
c) The distance traveled by the cyclist can be calculated using the formula:
distance = circumference of the wheel × N
where N is the number of revolutions and the circumference of the wheel can be calculated as 2πr, where r is the radius of the wheel.
Distance = circumference of the wheel × N
Distance = (2π × 0.36) × 89
Distance ≈ 201.06 m
To know more about angular acceleration here
https://brainly.com/question/30237820
#SPJ4
An outside thermometer reads 57°F. What is this temperature in °C? Round your answer to the nearest whole number. 14 49 71 135
Answer:
An outside thermometer reads 57°F. What is this temperature in °C? Round your answer to the nearest whole number.
14
49
71
135
answer is A:14
Explanation:
The temperature of the thermometer which reads 57 °F in degree celsius (°C) to the nearest whole number is 14 °C
Conversion formulaWe can convert from degree celsius (°C) to degree Fahrenheit (°F) with the following equation
°C = 5/9(°F – 32)
How to determine the temperature in degree celsius (°C) Temperature (°F) = 57 °FTemperature (°C) =?°C = 5/9(°F – 32)
°C = 5/9(57 – 32)
°C = 5/9 × 25
°C = 14 °C
Thus, the temperature in degree celsius (°C) of the thermometer is 14 °C
Learn more about conversion:
https://brainly.com/question/2139943
which of the following assets is the most liquid? part 2 a. an automobile. b. a u.s. savings bond. c. a traveler's check. d. 50 shares of microsoft stock.
The most liquid asset among the given options is likely to be a traveler's check. Option C is the correct answer.
Among the given options, the most liquid asset is a traveler's check (option C). Liquidity refers to how quickly and easily an asset can be converted into cash without significant loss in value. An automobile (option A) can take time and effort to sell, and its value can depreciate.
A U.S. savings bond (option B) has a fixed maturity date and may require time to redeem. 50 shares of Microsoft stock (option D) can be sold relatively quickly, but the liquidity depends on market conditions and trading volume. A traveler's check (option C) can be easily exchanged for cash at various locations, making it the most liquid asset in this context.
Learn more about liquid assets at
https://brainly.com/question/29760652
#SPJ4
The question is -
Which of the following assets is the most liquid?
A. an automobile.
B. a u.s. savings bond.
C. a traveler's check.
D. 50 shares of Microsoft stock.
use atoms and molecules in a sentence
Answer:
An atom is the smallest part of an element by itself, while molecules are built of multiple atoms.
snell’s law gives the change in intensity of a beam of light when it travels from one medium to another. group of answer choices true false
The statement "Snell's law gives the change in intensity of a beam of light when it travels from one medium to another" will be evaluated to determine its truthfulness. Option A is correct answer.
Snell's law, also known as the law of refraction, relates the angles of incidence and refraction of a light beam as it passes from one medium to another. It states that the ratio of the sine of the angle of incidence to the sine of the angle of refraction is equal to the ratio of the velocities of light in the two media.
However, Snell's law does not directly give information about the change in intensity of the light beam. Intensity refers to the amount of power carried by the light per unit area and is related to the square of the amplitude of the electric field. The change in intensity of a light beam when it passes through different media is influenced by factors such as absorption, scattering, and reflection, which are not explicitly described by Snell's law.
Therefore, the statement "Snell's law gives the change in intensity of a beam of light when it travels from one medium to another" is false. Snell's law primarily relates the angles of incidence and refraction, providing information about the direction of the light beam but not directly addressing changes in intensity.
Learn more about Snell's law here
https://brainly.com/question/31391616
#SPJ11
The complete question is
Snell’s law gives the change in intensity of a beam of light when it travels from one medium to another. group of answer choices true false
A. The higher the index of refraction of a medium
B. The slower light moves within it.
How many neutrons are in the nucleus of an atom with an atomic mass of 80 A.M.U. and an atomic number of 35?
Answer:
45
Explanation:
The mass number is 80
Proton number is 35
A-P=n
80-35=45
Triply charged uranium-235 and uranium-238 ions are being separated in a mass spectrometer. (The much rarer uranium-235 is used as reactor fuel.) The masses of the ions are 3.90×10−25kg3.90×10−25kg and 3.95×10−25kg,3.95×10−25kg, respectively, and they travel at 3.0×105m/s3.0×105m/s in a 0.250-T field. What is the separation between their paths when they hit a target after traversing a semicircle? (b) Discuss whether this distance between their paths seems to be big enough to be practical in the separation of uranium-235 from uranium-238.
Answer:
[tex]0.025\ \text{m}[/tex]
Yes
Explanation:
[tex]m_8[/tex] = Mass of uranium 238 ion = [tex]3.95\times 10^{-25}\ \text{kg}[/tex]
[tex]m_5[/tex] = Mass of uranium 235 ion = [tex]3.9\times 10^{-25}\ \text{kg}[/tex]
v = Velocity of ions = [tex]3\times 10^5\ \text{m/s}[/tex]
q = Charge of triply charged ions = [tex]3\times 1.6\times 10^{-19}\ \text{C}[/tex]
B = Magnetic field = 0.25 T
The force balance is
[tex]\dfrac{mv^2}{r}=qvB\\\Rightarrow r=\dfrac{mv}{qB}[/tex]
The difference between the radius of the ions are
[tex]\Delta r=(m_8-m_5)\dfrac{v}{qB}\\\Rightarrow \Delta r=\dfrac{(3.95\times 10^{-25}-3.9\times 10^{-25})\times 3\times 10^5}{3\times 1.6\times 10^{-19}\times 0.25}\\\Rightarrow \Delta r=0.0125\ \text{m}[/tex]
Separation is given by
[tex]\Delta d=2\Delta r=2\times 0.0125\\\Rightarrow \Delta d=0.025\ \text{m}[/tex]
The separation between their paths when they hit a target after traversing a semicircle is [tex]0.025\ \text{m}[/tex].
Yes, the distance between the paths is 2.5 cm is a practical separation between as it is easily measurable.
TRUE/FALSE. foxconn retrofitted the empire state building with led lighting, cutting down on energy consumption by 73 percent.
The statement "foxconn retrofitted the empire state building with led lighting, cutting down on energy consumption by 73 percent." is false as Foxconn did not retrofit the Empire State Building with LED lighting
There is no record or evidence to support the claim that Foxconn, a multinational electronics contract manufacturing company, retrofitted the Empire State Building with LED lighting resulting in a 73 percent reduction in energy consumption. Foxconn is primarily known for its manufacturing operations, particularly in the field of electronics and technology.
The retrofitting of the Empire State Building with LED lighting did occur, but the company responsible for this project was Philips Lighting (now known as Signify). The retrofitting project, completed in 2012, involved replacing the building's traditional lighting fixtures with energy-efficient LED lights, resulting in significant energy savings. However, the reported energy reduction was approximately 38 percent, not 73 percent.
Therefore, the statement claiming that Foxconn retrofitted the Empire State Building with LED lighting, reducing energy consumption by 73 percent, is false.
To know more about led lighting, refer here:
https://brainly.com/question/30871146#
#SPJ11
The resistance of resistor is greater for:
a.Short and thin resistor
b.Short and thick resistor
c.Long and thin resistor
d.None
Answer:
c: long and thin resistor.
Explanation:
The resistance of a resistor is given by:
R = ρ*L/A
where:
R = resistance
ρ = resistivity (depends on the material)
L = length of the material
A = cross-sectional area of the material
We can see that the length is on the numerator, which means that if we increase the length, then the resistance is increased.
We also can see that the cross-sectional area is on the denominator, then if we increase the area (for example, with a ticker resistor) the resistance decreases.
Then if we want to maximize the resistance, we need to have a long and thin resistor, so the correct answer is c.